background image

Part No. 324991 R0812B 

Printed in USA © 2012 ICON IP, Inc.

ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and 

material, under normal use and service conditions. The frame is warranted for a lifetime. The drive motor 

is warranted for twenty-five (25) years from the date of purchase. Parts and labor are warranted for one (1) 

year from the date of purchase.

This warranty extends only to the original purchaser (customer). ICON’s obligation under this warranty is 

limited to repairing or replacing, at ICON’s option, the product through one of its authorized service centers. 

All repairs for which warranty claims are made must be preauthorized by ICON. If the product is shipped 

to a service center, freight charges to and from the service center will be the customer’s responsibility. If 

replacement parts are shipped while the product is under warranty, the customer will be responsible for a 

minimal handling charge. For in-home service, the customer will be responsible for a minimal trip charge. 

This warranty does not extend to freight damage to the product. This warranty will automatically be voided 

if the product is used as a store display model, if the product is purchased or transported outside the USA, 

if all instructions in this manual are not followed, if the product is abused or improperly or abnormally used, 

or if the product is used for commercial or rental purposes. No other warranty beyond that specifically set 

forth above is authorized by ICON.

ICON is not responsible or liable for indirect, special, or consequential damages arising out of or in con-

nection with the use or performance of the product; damages with respect to any economic loss, loss of 

property, loss of revenues or profits, loss of enjoyment or use, or costs of removal or installation; or other 

consequential damages of any kind. Some states do not allow the exclusion or limitation of incidental or 

consequential damages. Accordingly, the above limitation may not apply to the customer.

The warranty extended hereunder is in lieu of any and all other warranties, and any implied warranties of 

merchantability or fitness for a particular purpose are limited in their scope and duration to the terms set 

forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the 

above limitation may not apply to the customer.

This warranty provides specific legal rights; the customer may have other rights that vary from state to state.

ICON Health & Fitness, Inc., 1500 S. 1000 W., Logan, UT 84321-9813

LIMITED WARRANTY

 IMPORTANT: You must register this product within 30 days of the purchase date to avoid added 

fees for service needed under warranty. Go to www.proformservice.com/registration.

To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to pro-

vide the following information when contacting us:

•  the model number and serial number of the product (see the front cover of this manual)

•  the name of the product (see the front cover of this manual)

•  the key number and description of the replacement part(s) (see the PART LIST and the EXPLODED DRAWING 

near the end of this manual)

ORDERING REPLACEMENT PARTS

Summary of Contents for 615 T Treadmill

































Reviews: