background image

14

25.

Make sure all parts are properly tightened before
you use the weight bench. The use of all remain-
ing parts will be explained in Adjusting the Weight
Bench starting on page 15.

23. Slide a Handle (36) onto a Handle Frame (69) and

secure it by tapping a Push Nut (70) onto the end of
the Handle Frame. 

Repeat this procedure for the second Handle (36). 

23

24. Press a Weight Adapter Bushing (47) into each end

of the two Barbell Adapters (61). 

Slide a Barbell Adapter (61) onto each end of the
Barbell (74) and secure them with two M6 x 32mm
Bolts (7) and two M6 Nylon Locknuts (2). 

Note: If

you are not going to use olympic weights, you do
not need to mount the Weight Adapter.

24

70

70

36

69

47

47

2

36

69

74

61

7

USING THE BARBELL RACKS

Before beginning an exercise, move the Safety Stops (23)
to a set of holes in the Barbell Uprights (41) that is best
suited for that exercise. The selected holes should repre-
sent the lowest point to which you want your Barbell (74)
to go during the exercise. Rotate your Barbell until the
Barbell Hooks (29) disengage from the Barbell Uprights.
Perform the exercise as shown in the accompanying
EXERCISE GUIDE. When you have completed the exer-
cise, rotate your barbell until the Barbell Hooks lock into a
set of holes in the Barbell Uprights.

WARNING: Always set both safety stops at the
same height. Always make sure the barbell hooks
lock into holes in the Uprights at the same height.
To do this, make sure your barbell is in a level
position before you try to engage the barbell
hooks.

41

31

74

23

29

This section explains how to adjust the weight bench. See the EXERCISE GUIDELINES on page 17 for impor-
tant information on how to get the most benefit from your exercise program. Also, refer to the accompanying
exercise poster to see the correct form for each exercise. 

Inspect and tighten all parts each time you use the weight bench. Replace any worn parts immediately. The
weight bench can be cleaned with a damp cloth and a mild, non-abrasive detergent. Do not use solvents.

Adjusting the Weight Bench

Summary of Contents for 660 Weight Bench























Reviews: