background image

8

7.

Attach the Seat (14) to the Seat Brackets (9, 46) with
four M6 x 16mm Screws (3) and four M6 Washers
(68). 

Insert the Long ÒLÓ-Pin (71) through the holes in the
Seat Brackets (9, 46) and the Frame (54). 

7

10. Press a 3/4Ó Round Inner Cap (65) into each end of

the three Pad Tubes (67, 77). 

Insert a Short Pad Tube (67) into the upper hole in
the Leg Lever (18) as shown. Slide a Foam Pad onto
each end of the Short Pad Tube.

Insert a Long Pad Tube (77) into the lower hole in the
Leg Lever (18) as shown. Slide a Foam Pad onto
each end of the Long Pad Tube.

Insert a Pad Tube (67) through one of the holes in the
bracket (C) on the Pad Upright (19). Slide a 6Ó Foam
Pad (10) onto each end of the Pad Tube.

10

14

9

71

54

46

68

68

3

3

10

10

C

18

67

67

77

65

65

10

19

65

65

9.

Attach the Lock (62) to the Pad Upright (19) with the
M8 x 62mm Bolt (58), a Thin M8 Washer (22), a Lock
Spacer (66) and an M8 Nylon Locknut (13). 

Do not

overtighten the Nylon Locknut. You must be able
to freely pivot the Lock. 

Lubricate the M10 x 72mm Bolt (59). Attach the Leg
Lever (18) to the bracket (C) on the Pad Upright (19)
with the Bolt and an M10 Nylon Locknut (1). 

Do not

overtighten the Nylon Locknut. You must be able
to freely pivot the Leg Lever. 

9

13

18

1

C

66

22

19

62

58

59

8.

Press a 2Ó Square Inner Cap (17) into each of the
open ends of the Leg Lever (18). 

Slide the Weight Tube (51) into the indicated hole in
the Leg lever (18). Secure the Weight Tube with the
M8 x 70mm Bolt (52), two Thin M8 Washers (22), a
1/2Ó Spacer (50) and an M8 Nylon Locknut (13). 

Press a 1Ó Round Inner Cap (12) into the indicated
end of the Weight Tube (51). Press the Angle Cap
(49) onto the indicated end of the Weight Tube.

Press a Weight Adapter Bushing (47) into each end
of a Short Weight Adapter (48). Slide the Weight
Adapter onto the Weight Tube (51) and secure it with
an M6 x 32mm Bolt (7) and an M6 Nylon Locknut (2).

Note: If you are not going to use olympic weights,
you do not need to mount the Weight Adapter.

8

51

12

2

17

17

17

49

18

47

48

47

7

52

22

50

22

13

Summary of Contents for 660 Weight Bench























Reviews: