background image

1. It is the responsibility of the owner to ensure

that all users of this treadmill are adequately
informed of all warnings and precautions.

2. Use the treadmill only as described.

3. Place the treadmill on a level surface, with at

least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.  

4. Keep the treadmill indoors, away from mois-

ture and dust. Do not put the treadmill in a
garage or covered patio, or near water. 

5. Do not operate the treadmill where aerosol

products are used or where oxygen is being
administered. 

6. Keep children under the age of 12 and pets

away from the treadmill at all times.

7. The treadmill should be used only by persons

weighing 300 pounds or less. 

8. Never allow more than one person on the

treadmill at a time. 

9. Wear appropriate exercise clothes when

using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. 

Always wear athletic

shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals. 

10. When connecting the power cord (see page 10),

plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord. 

11. Use only a single-outlet surge suppressor that

meets all of the specifications described on
page 10. To purchase a surge suppressor, see
your local PROFORM dealer or call the toll-
free telephone number on the front cover of
this manual and order part number 146148, or
see your local electronics store.

12. Failure to use a properly functioning surge

suppressor could result in damage to the con-

trol system of the treadmill. If the control sys-
tem is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.

13. Keep the power cord and the surge suppres-

sor away from heated surfaces.

14. Never move the walking belt while the power

is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See BE-
FORE YOU BEGIN on page 5 if the treadmill is
not working properly.)   

15. Read, understand, and test the emergency

stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 12).

16. Never start the treadmill while you are stand-

ing on the walking belt. Always hold the
handrails while using the treadmill.

17. The treadmill is capable of high speeds.

Adjust the speed in small increments to avoid
sudden jumps in speed. 

18. The pulse sensor is not a medical device.

Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.

19. Do not use the hand weights at speeds faster

than walking speeds. Using weights and not
holding the handrails may compromise your
ability to maintain your balance. Exercises
using weights should be attempted only by
experienced users.

20. Never leave the treadmill unattended while it

is running. Always remove the key and unplug
the power cord when the treadmill is not in
use. 

21. Do not attempt to raise, lower, or move the

treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 23.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.

22. When folding or moving the treadmill, make

sure that the storage latch is fully closed.

WARNING:

To reduce the risk of burns, fire, electric shock, or injury to persons, read the

following important precautions and information before operating the treadmill.

IMPORTANT PRECAUTIONS

3

Summary of Contents for PFTL68505.0































Reviews: