background image

   

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

2. Handrails, Foot Bars and Rotation Rod Installation: 
Step D: 

Attach the Right Foot Bar (17) onto the bottom end of the Right Handrail (9) 

with one Bolt (11) and one Nylon Nut (14).     

Note:

 Make sure the right foot bar is angled downward for correct installation.   

Use one flat wrench to secure the bolt and the other flat wrench to tighten the nylon 
nut until firm.    For correct tightness, the bolt’s threads 

MUST

 protrude out through the 

nylon nut until no longer turns. 

Step E: 

Repeat step above for the left side. 

Step F:

 Cover both Bolts (11) and Nylon Nuts (14) with four Nut Caps (88). 

Step G:

 Using S6 Allen Wrench, remove two Bolts (5), two Spring Washers (6), two 

Washers (7), and two Wave Washers (22) PRE-ASSEMBLED from both ends of the 
Rotation Rod (60).     
Insert the Rotation Rod (60) into the hole on top of the Mainframe (59).    Slide the 
Right Handrail (9) onto the Rotation Rod (60) and secure in place with one set of the 
above hardware that was removed.    Use one S6 Allen Wrench to secure the bolt on 
one end of the rod and the other S6 Allen Wrench to the bolt on the other end of the 
rod to tighten the bolts until firm.     

Step H: 

Repeat step above for the left side. 

 

Hardware:

 

 
 
 
 
 

10 

ASSEMBLY

(Step D&E) 

(11) 

Bolt 

  2 

PCS 

(14) Nylon Nut 

2 PCS 

60

60

76

76

77

77

5

6

7

8

9

88

88 1111

14

14

88

88

17

17

59

59

22

22

22

22

11

11

88

88

14

14

88

88

8

5

6

7

E

H

Open-Ended Flat Wrench

Tools: 

S6 Allen Wrench 

S6 Allen Wrench with 

Phillips Screwdriver   

Summary of Contents for Air Elliptical





























Reviews: