Progress Lighting AirPro P250003 Installation Manual Download

Page: 13 / 16

10. Remote Control

LEARN

CFL

D 1

LEARN

CFL

D 1

Figure 20

Preparing the Remote

Control

1. Remove the battery cover by pressing

firmly on the arrow and sliding the cover

off.

2. Install two 1.5V AAA batteries (N)

(included).

3. Slide the dip switch in the battery

compartment to the “1” setting.

4. Confirm that the power to the fan is off at

either the wall switch or breaker box.

5. Return power to the fan at the wall switch

or breaker box.

6. Press and release the “Learn” button located

in the remote’s battery compartment within

30 seconds of turning on the power.

7. If pairing is successful, the fan’s light kit

will flash and the blades will begin to spin.

8. Replace the battery cover on the remote

control.

NOTE: The remote control has already

been paired to the ceiling fan for your

convenience. If you have two of the

same model fans in your home , please

follow the steps below to control each fan

independently.

Summary of Contents for AirPro P250003

















Search results

Summary of Contents for AirPro P250003

Reviews:

Related manuals for AirPro P250003

Brands by name

Popular brands

Progress Lighting AirPro P250003, Installation Manual

Search results

Summary of Contents for AirPro P250003

Reviews:

Related manuals for AirPro P250003

Brands by name

Popular brands