Progress Lighting AirPro Willacy P250063, Installation Manual

1. Safety Rules

To reduce the risk of electric shock, ensure electricity has been turned off 

at the circuit breaker or fuse box before beginning.

1.

All  wiring  must  be  in  accordance  with  the  National  Electrical  Code 

“ANSI/NFPA 70-1999” and local electrical codes.  Electrical installation 

should be performed by a qualified licensed electrician.

2.

The  outlet  box  and  support  structure  must  be  securely  mounted  and 

capable of reliably supporting a minimum of 35 lbs (15.9 kg) or less. Use 

only UL-listed outlet boxes marked “FOR FAN SUPPORT.”

3.

The fan must be mounted with a minimum of 7 ft. (2.1m) clearance from 

the trailing edge of the blades to the floor.

4.

Avoid placing objects in the path of the blades.

5.

To  avoid  personal  injury  or  damage  to  the  fan  and  other  items,  be 

cautious when working around or cleaning the fan.

6.

Do not use water or detergents when cleaning the fan or fan blades. A dry 

dust cloth or lightly dampened cloth will be suitable for most cleaning.

7.

After making electrical connections, spliced conductors should be turned 

upward and pushed carefully up into the outlet box. The wires should be 

spread apart with the grounded conductor and the equipment-grounding 

conductor on one side of the outlet box and ungrounded conductor on the 

other side of the outlet box.

8.

All set screws must be checked and retightened where necessary before 

installation.

9.

This device complies with Part 15 of the FCC Rules. Operation is subject 

to the following two conditions: 

(1) This device may not cause harmful interference, and (2) this device 

must accept any interference received, including interference that may 

cause undesired operation. Please note that changes or modifications not 

expressly approved by the party responsible for compliance could void 

the user's authority to operate the equipment.

Note: 

This equipment has been tested and found to comply with the 

limits for Class B digital device, pursuant to part 15 of the FCC Rules. 

These limits are designed to provide reasonable protection against 

harmful interference in a residential installation.This equipment 

generates, uses and can radiate radio frequency energy and, if not 

installed and used in accordance with the instructions, may cause harmful 

interference to radio or television reception, which can be determined by 

turning the equipment off and on, the user is encouraged to try to correct 

the interference by one or more of the following measure.

- Reorient or relocate the receiving antenna. 

- Increase the separation between the equipment and the receiver.

- Connect the equipment into an outlet on a circuit different from that to 

   which the receiver is connected. Consult the dealer or an experienced 

   radio/TV technician for help. 

10.

WARNING

TO REDUCE THE RISK OF PERSONALL INJURY, DO NOT BEND THE  BLADE  ARMS  (ALSO  REFERRED  TO  AS 

FLANGES),  WHEN  INSTALLING  THE  BRACKETS,  BALANCING  THE  BLADES  OR  CLEANING  THE  FAN.    DO 

NOT  INSERT  FOREIGN  OBJECTS  IN  –  BETWEEN ROTATING FAN BLADES.   

NOTE

READ AND SAVE THESE INSTRUCTIONS

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR OTHER PERSONAL  INJURY,  MOUNT  FAN  ONLY  ON  AN 

OUTLET  BOX  OR  SUPPORTING SYSTEM MARKED ACCEPTABLE FOR FAN SUPPORT OF 35 LBS (15.9 KG)  OR LESS 

AND USE MOUNTING SCREWS PROVIDED WITH THE OUTLET BOX.  MOST  OUTLET  BOXES  COMMONLY  USED  FOR 

THE  SUPPORT  OF  LIGHTING  FIXTURES  ARE  NOT  ACCEPTABLE  FOR  FAN  SUPPORT  AND MAY NEED TO BE 

REPLACED. CONSULT A QUALIFIED ELECTRICIAN IF IN  DOUBT.