background image

SAVE THESE INSTRUCTIONS 

When installing and using your Progressive Bed product, basic safety precautions should always be followed. Please read 

all instructions thoroughly before using. Apply all other relevant precautions when operating electrical devices and moving 

mechanisms. 

DANGER –

 To reduce the risk of electric shock, always unplug the base from the electrical outlet before cleaning or 

servicing. 

WARNING –

 To reduce the risk of burns, fire, electric shock, or injury to persons: 

Never operate this furnishing if the cord or plug has been damaged, is not working properly, or has been in 

contact with water. 

Keep the cord away from heated surfaces. 

To disconnect, turn off all controls and adjust to a flat position, then remove the plug from the electrical outlet. 

Never operate this furnishing with the air openings blocked. Keep free of lint, hair, and other potential hazards. 

Never drop or insert any object into any opening. 

Close supervision is necessary when this furnishing is used by/near children or those with certain disabilities. 

Do not allow any person or animal under the adjustable bed at any time. 

Store the remote control out of children’s reach when not in use. 

Only use indoors. 

During operation, make sure the user’s entire body is positioned within the confines of the bed. Do not place 

extremities over the sides of the bed when operating the bed. 

Do not operate where aerosol (spray) products are being used, near explosive gases or where oxygen is being 

administered. 

Using the adjustable bed with oxygen administering equipment other than the nasal mask type creates a possible 

fire hazard. 

Use caution when having liquids in or around the adjustable bed to ensure no spilling occurs. In case of spillage, 

unplug the bed immediate

 the spill and allow the area to 

dry thoroughly before using the electric controls again. 

Do not eat or drink hot liquids while operating the adjustable bed.  

Use this furnishing only for its intended use as described in these instructions. Do not use attachments that are 

not recommended by the manufacturer. 

Safety Precautions 

P a g e   |   3

Operating Notes 

Moving Parts 

It is advisable that children and pets are vacated from the area before operating the adjustable bed. Ensure all moving 

parts are free of obstruction.  

Weight Restriction 

The electrical and mechanical components must be operated within the specified weight limit and the weight must be 

evenly distributed over the frame. The individual sections of the adjustable bed are not designed to support or lift this 

weight. Exceeding the weight restriction may cause injury. It may also damage the product and void the warranty. 

Warranty 

Opening or tampering with the components and operating outside of the advertised usage limitations will void the 

warranty. 

Operation Time 

The electrical and mechanical components must be operated within the specified operation time and frequency. 

Exceeding this rating will shorten the life expectancy of the adjustable bed and will void the warranty. 

Not for Hospital Use 

This Progressive Bed product is designed for household use only. It is not designed for hospital use and is not designed 

to meet hospital standards. 

Summary of Contents for DRIFT PRO




















Reviews: