background image

DECLARATION OF CONFORMITY 

 

The product to which this manual refers is in accordance with the Directives of 
the  European  Community.  The  examination  is  made  clear  by  the  application  of 
the CE mark on the product and the declaration of compliance. 

The  device  meets  the  requirements  of  the  2002/95/CE  (RoHS)  Directive;  the 
General  Safety  Information  Regulations:  EN60598-1,  EN60598-2-17  and  the 
European Parliament's Directive 2004/108/EC on Electromagnetic Compatibility. 

DISPOSAL OF UNUSED PRODUCT 

 

The device must be disposed of in accordance with the applicable laws relating 
to lighting products. In any case, it should not be thrown between normal waste 
or dispersed in the environment, the latter action, although legally pursued, is a 
serious danger to animals and people and a source of long-term pollution. The 
product  cannot  be  treated  as  a  simple  urban  waste  and  must  be  disposed  of 
appropriately in accordance with existing waste disposal regulations.

Avigliana, 22/09/2021 

PROIETTA 

srl

Viale Dei Mareschi 4/d - 10051 - Avigliana - TO (Italy) - VAT number: IT09964950019

tel. +39 011 9761039, info@proietta.com, www.proietta.com 

8

Summary of Contents for IRIDIUM 150











Reviews: