background image

SAFETY INFORMATION 

Read  the  following  safety  information  carefully  before  performing  any  operations.  The 
product described in this manual is a lighting fixture for the projection of a light beam in 
indoor and outdoor environments. 

Any  other  use  is  not  provided  by  the  manufacturer  and  therefore  relieves  him  of  any 
liability for damages arising from misuse.

Any repair that requires the dismantling of the projector assembly screws should only be 
carried  out  by  the  manufacturer,  who  denies  any  responsibility  for  unauthorized 
interventions. 

Warning: The surface temperature of some projector components can reach high enough 
values to burn when touched directly, during and after shutdown.

Always  disconnect  the  projector  from  the  outlet  before  any  maintenance  operation.  You 
risk taking the electric shock if you disassemble the projector or some of its parts.

For  reliable  operation  of  the  device,  the  ambient  temperature  must  be  between  -25°C      
(-13°F) and 45°C (113°F).

The  projector  must  be  positioned  in  such  a  way  that  the  objects  a

ected  by  the  light 

beam are at least 5 meters away from the projector lens.

Never place the projector on flammable and/or combustible surfaces.

Be sure to firmly secure the projector to an architectural element that ensures its stability 
and reliability. All elements used for installation (screws, bolts, brackets, etc.) must always 
be adjusted to the load they need to support.

Use  an  M12  bolt  with  a  self-locking  nut  and  use  a  security  chain  in  the  event  of  a 
suspended installation.

Do  not  place  objects  on  the  power  cable  and  in  case  if  it  was  damaged

 

contact  the 

manufacturer for replacement in order to avoid danger of electrocution.

Air  intakes  should  never  be  covered  or  clogged  with  any  material.  Be  sure  to  provide 
adequate ventilation to the projector to protect it from overheating. The projector should 
not  be  placed  in  a  closed  installation  or  in  a  compartment  that  is  too  small  and  without 
enough ventilation.

Do not look at the beam of light to avoid damaging your eyes.

Never touch the projector and all its components with wet hands.

1

Summary of Contents for IRIDIUM 150











Reviews: