User Manual
SLIM WOOD-LIGHT PANEL »
UV PANEL
WARNING! Before carrying out any operations with the unit, carefully read this instruction manual and keep it with cure for future
reference. It contains important information about the installation, usage and maintenance of the unit.
In order to improve the quality of products, Music&Lights S.r.l. reserves the right to modify the characteristics stated in this instruction manual
at any time and without prior notice. All revisions and updates are available in the ‘manuals’ section on site www.musiclights.it
For further information, please contact our Service Center: tel. +39 0771 72190 fax +39 0771 721955 - service@musiclights.it
Rev001 - 07/12 ©2012 Music & Lights S.r.l. - Italy - www.musiclights.it
EN
Description and technical specifications
Slim wood-light panel based on LED source, conceived for application in
clubs, bars, mobile DJ’s set.
• Light source: 9x1W UV LED
• Plug&Play: ON/OFF functioning
• Beam Angle: 120°
• Power unit: 100-240V 50/60Hz
• Power consumption: 23W
• Weight: 0,9 kg
• Dimensions (WxHxD): 198x230x50 mm
Installation
When carrying out any installation, always comply scrupulously with all the
regulations (particularly regarding safety) currently in force in the country
in which the fixture’s being used.
• Install the unit at a suitable location by means of the mounting bracket.
• Always additionally secure the projector with the safety rope from falling
down. For this purpose, fasten the safety rope at a suitable position so
that the maximum fall of the projector will be 20 cm.
• Adjust the projector and use the knob to slightly release or tighten the
locking mechanism of the bracket if is necessary.
Operation
Connect the supplied main cable to a socket (100-240V~/50-60Hz). The
UVPANEL is ready for operation. To switch off, disconnect the mains plug
from the socket.
Maintenance and cleaning the unit
• Make sure the area below the installation place is free from unwanted
persons during setup.
• All screws used for installing the device and any of its parts should be
tightly fastened and should not be corroded.
• Housings, fixations and installation spots (ceiling, trusses, suspensions)
should be totally free from any deformation.
• Use a soft cloth dampened with any detergent liquid for cleaning glass to
remove the dirt from the reflectors, from the lenses and filters.
General instruction
• The products referred to in this manual conform to the European
Community Directives and are therefore marked with . • The unit is
supplied with hazardous network voltage (230V~). Leave servicing to
skilled personnel only. Never make any modifications on the unit not
described in this instruction manual, otherwise you will risk an electric
shock. • Connection must be made to a power supply system fitted with
efficient earthing (Class I appliance according to standard EN 60598-
1). It is, moreover, recommended to protect the supply lines of the units
from indirect contact and/or shorting to earth by using appropriately
sized residual current devices. • The connection to the main network of
electric distribution must be carried out by a qualified electrical installer.
Check that the main frequency and voltage correspond to those for which
the unit is designed as given on the electrical data label. • Never use the
fixture under the following conditions: - in places subject to vibrations or
bumps; - in places with a temperature of over 40°C. • Make certain that
no inflammable liquids, water or metal objects enter the fixture. • Do not
dismantle or modify the fixture. • All work must always be carried out
by qualified technical personnel. Contact the nearest sales point for an
inspection or contact the manufacturer directly. • If the unit is to be put
out of operation definitively, take it to a local recycling plant for a disposal
which is not harmful to the environment.
Warnings and installation precautions
• If this device will be operated in any way different to the one described
in this manual, it may suffer damage and the guarantee becomes void.
Furthermore, any other operation may lead to dangers like short circuit,
burns, electric shock, etc. • Before starting any work or cleaning the
projector, cut off power from the main supply. When carrying out any work,
always comply scrupulously with all the regulations (particularly regarding
safety) currently in force in the country in which the fixture’s being used. •
Keep any inflammable material at a safe distance from the fixture. • Shields,
lenses or ultraviolet screens shall be changed if they have become damaged
to such an extent that their effectiveness is impaired. • The lamp (LED) shall
be changed if it has become damaged or thermally deformed. • Never look
directly at the light beam. Please note that fast changes in lighting, e. g.
flashing light, may trigger epileptic seizures in photosensitive persons or
persons with epilepsy. • Do not connect the device to any dimmer pack. •
Due to the magnifying type lens, please keep the lens out of contact with
direct sunlight. Direct sunlight can cause heat to build up inside of the unit,
which will seriously damage unit.
Fig.1
1
2
3
Rear view
4
5
1.
MOUNTING BRACKET
2.
LOCKING KNOB for the mounting bracket.
3. LED panel
4. MAIN CABLE with Shuko plug
5. SAFETY EYE to attach safety cable
