background image

 

Warranty & Return Policy

 

 

 

Proluxe warrants all products manufactured 
by it against defects in workmanship or 
materials from the date of purchase for a 
period of 1 year on parts and labor. This 
warranty applies to only equipment 
purchased and used in the United States.  
 
Warranty period shall begin when equipment 
ships. Warranty travel will only be covered 
for 60 miles.  
 
ALL WARRANTY SERVICE CALLS MUST BE 
APPROVED BY PROLUXE. IF THIS 
PROCEDURE IS NOT FOLLOWED, 
WARRANTY SERVICE WILL NOT BE 
COVERED. WARRANTY SERVICE WILL BE 
PAID ON STRAIGHT TIME, OVERTIME 
WILL NOT BE COVERED. 
 

 
E X C L U S I O N S 
 

Wood & Gas Fired Ovens 

Warranty applies to the main body of the 
oven being steel / refractory and insulation 
shall be free from defects in materials and 
workmanship for a period of four years from 
the date of purchase. The gas equipment 
shall be free from defects in materials and 
workmanship for a period of one (1) year 
from the date of purchase. Lifetime warranty 
against cracks on the oven floor. 
 

Air Compressors 

Are excluded from this warranty, but Proluxe 
may act as a warranty expeditor in certain 
instances regarding these compressors. The 
air compressor manufacturer provides a 

limited warranty and a copy of this warranty 
is furnished with all compressors sold by 
Proluxe. For prompt handling of compressor 
warranty claims the instructions of the 
compressor manufacturer must be adhered 
to. 
 

Special Order Equipment and 
Accessories  

Cannot be canceled and are not returnable 
unless defective within the terms of this 
warranty. 
 
In no event shall Proluxe be liable for 
consequential damages arising out of the 
failure of any of its products if operated 
improperly or caused by normal wear or 
damaged by operator abuse. 
 

Limited Lifetime Warranty on 
Heating Elements 

If replacement is needed, Proluxe will send 
the new part at no charge but labor will not 
be covered unless the unit is still under the 1 
year manufacturer warranty. 
 

 
R E T U R N E D   M E R C H A N D I S E  
P O L I C Y 
 

Should it become necessary to return any of 
the company’s products, the following 
instructions must be adhered to: First, 
contact our customer service department for 
approval and a return authorization number. 
Please have the serial number of your item 
available at that time. All merchandise must 
be shipped freight prepaid by customer or 

17 

Summary of Contents for Apex X1




















Reviews: