6.
WIRING
The lock operates when applying and interrup
switch (button). Controller installation is done accord
Attention: power of the lock is supplied by the voltage from 11 to 14 V of the direct current.
Connect the power cable of the lock in the following
red – positive, black – negative.
(The reverse polarity voltage supply does
Provide reliable electrical contact. Isolate the connection points to avoid short
ATENTION!!! The possibility to use
based on the level of premise accountability, assignment of access restriction
7.
POSSIBLE FAILURES, INSTALLATION PROBLEM
Failures and problems
The lock does not fix the deadbolt
roller (the door does not fix when it is
closed).
The door does not close fully,
because the deadbolt does not reach
the lock.
The deadbolt roller does not enter, or
it enters with friction into the lock
groove.
When the status of the door is
"open", but the door does not open.
To open the door needed to press it
tighter to the door frame.
8.
MAINTENANCE
Maintenance of a lock is performed at least
- Examination of the lock to check fixation
- Check the locking bolt correct position
9.
MANUFACTURER'S WARRANTY
Engineering & Technical Center PROMIX, LLC guarantees the conformity of
requirements of applicable TU standards under the regulation
The warranty period is 18 months commencing from the date of acceptance by Quality Control Department.
Within the warranty period, Engineering & Technical Center PROMIX, LLC undertakes to re
charge. The shipping cost to the place of repair and back shall be borne by the Buyer.
The warranty shall not cover defects or damages, resulting from:
- improper maintenance by the Buyer;
- using the lock in conditions that do not conform to the operating requirements;
- mechanical damages or disassembly of
- violation of transportation and storage regulations.
PACKING
Electromechanical lock "Sheriff-5" with the specified date of manufacture is made and accepted in accordance with TU
003–80210527–14, obligatory requirements of state standards and applicable technical documents, found fit for service and
packed by Engineering & Technical Center PROMI
QCD seal
Engineering & Technical Center PROMIX, LLC
Russia, 214030, Smolensk city, Krasninskoye Hwy
Tel. (4812) 619-330
www.itc-promix.ru
Please send us all your comments and suggestions concerning our lock via e
Thank you in advance!
4
The lock operates when applying and interrupting the power supply, and for it is usually used a controller (contro
done according to the technical data sheet.
power of the lock is supplied by the voltage from 11 to 14 V of the direct current.
lock in the following polarity:
does not provide operability of the lock, but does not damage
solate the connection points to avoid short-circuiting.
this lock to restrict access to premises is determined
on the level of premise accountability, assignment of access restriction and other factors (security,
INSTALLATION PROBLEMS AND TROUBLESHOOT
Troubleshoot
deadbolt
roller (the door does not fix when it is
Set the lock on the "closed" status (turn on the voltage supply of the lock).
Check the polarity and make sure that the voltage supply corresponds with the
required one.
Make sure that when drilling the hole for the lock, the internal metal frame of
the door profile was drilled either.
Adjust the deadbolt (see Para. 6.2) in that way when the door is closed the
roller enters into the lock groove until the full operation of the fixation device.
does not reach
It is possible that the fixation device manually one
moves to the "close" position (not by the
manually or by an external object). Change the
fixation device position to "open", for this turn off the
voltage supply of the lock, and turn the fixation
device.
pull
roller does not enter, or
it enters with friction into the lock
Re-establish the door position one changed during operation. If it is impossible
to re-establish it, adjust the deadbolt (see Para. 6.2).
When the status of the door is
does not open.
to press it
Eliminate the causes of loose fit of the door to the door frame. Adjust the
deadbolt in the horizontal direction.
least once per two months and includes:
fixation reliability. If it is necessary, tighten up fixing elements of the lock and the
correct position. If it is necessary, adjust the position of the locking bolt
Engineering & Technical Center PROMIX, LLC guarantees the conformity of the electromechanical lock "Sheriff
requirements of applicable TU standards under the regulations of operation and installation established in this operating manual.
The warranty period is 18 months commencing from the date of acceptance by Quality Control Department.
Within the warranty period, Engineering & Technical Center PROMIX, LLC undertakes to re
charge. The shipping cost to the place of repair and back shall be borne by the Buyer.
The warranty shall not cover defects or damages, resulting from:
that do not conform to the operating requirements;
disassembly of the lock by the Buyer;
violation of transportation and storage regulations.
PACKING AND ACCEPTANCE CERTIFICATE
with the specified date of manufacture is made and accepted in accordance with TU
, obligatory requirements of state standards and applicable technical documents, found fit for service and
packed by Engineering & Technical Center PROMIX, LLC.
Engineering & Technical Center PROMIX, LLC
Krasninskoye Hwy, 35
PATENT
suggestions concerning our lock via e-mail:
mail@itc
is usually used a controller (control board) or a
power of the lock is supplied by the voltage from 11 to 14 V of the direct current.
damage it).
determined by the installer company
and other factors (security, CCTV, etc.).
n the "closed" status (turn on the voltage supply of the lock).
voltage supply corresponds with the
Make sure that when drilling the hole for the lock, the internal metal frame of
. 6.2) in that way when the door is closed the
into the lock groove until the full operation of the fixation device.
It is possible that the fixation device manually one
moves to the "close" position (not by the deadbolt,
manually or by an external object). Change the
fixation device position to "open", for this turn off the
voltage supply of the lock, and turn the fixation
establish the door position one changed during operation. If it is impossible
. 6.2).
Eliminate the causes of loose fit of the door to the door frame. Adjust the
fixing elements of the lock and the deadbolt.
locking bolt (see Para. 6.2).
lectromechanical lock "Sheriff-5" to the
established in this operating manual.
The warranty period is 18 months commencing from the date of acceptance by Quality Control Department.
Within the warranty period, Engineering & Technical Center PROMIX, LLC undertakes to repair the defective product free of
with the specified date of manufacture is made and accepted in accordance with TU 3428–
, obligatory requirements of state standards and applicable technical documents, found fit for service and
RUSS RU.
ММ
07.
Н
00002
PATENT OF INVENTION
№
238261
itc-promix.ru
.
