F
J
K
L
M
H
I
E
FRONT
REAR
5
6
Forward/Backward Trim
• If your ORBIT™ HD drifts forward, push and
release the BACKWARD TRIM button back
repeatedly until the motion stops and proper
flight is maintained (see diagram J).
• If your ORBIT™ HD drifts backwards, push and
release the FORWARD TRIM button forward in
the same manner until the problem is resolved.
Right/Left Trim
• If your ORBIT™ HD drifts left, push and release
the RIGHT TRIM button back repeatedly until
the motion stops and proper flight is
maintained (see diagram K).
• If your ORBIT™ HD drifts right, push and release
the LEFT TRIM button in the same manner until
the problem is resolved.
Right/Left Spin Trim
• If your ORBIT™ HD spins left, push and release
the RIGHT SPIN TRIM button back repeatedly
until the motion stops and proper flight is
maintained (see diagram L).
• If your ORBIT™ HD spins right, push and release
the LEFT SPIN TRIM button in the same manner
until the problem is resolved (see diagram M).
4 CHANNEL FLIGHT CONTROL
Below is a list of basic flight functions for your long-range remote control ORBIT™ HD. While learning to
fly your ORBIT™ HD it is best to start with a large space until you get used to the basic controls. As you
master flying your ORBIT™ HD you can move to more advanced maneuvering techniques. Practice makes
perfect! When you have these basic steps down you can move to the next level.
SPEED SELECT BUTTON
The Orbit™ HD has 3 speed settings; SLOW, MEDIUM and HIGH. The default setting when you first turn on your
Orbit™ HD is the SLOW speed mode. To increase the speed simply trigger the Speed setting button. (see remote
diagram on pg 3) You will hear two beeps indicating your Orbit™ HD has changed to MEDIUM speed mode. To
increase the speed simply trigger the Speed setting button one more time and you will hear three beeps indicating
your Orbit™ HD has changed to HIGH speed mode. Trigger the Speed setting button again and you will hear one
beep indicating your Orbit™ HD speed changed back to SLOW speed mode.
Move the right Direction Stick up while in flight
and the ORBIT™ HD will move forward.
Move the right Direction Control down while in
flight and the ORBIT™ HD will move backward
(see diagram H).
Move the right Direction Control left and the
ORBIT™ HD will bank to the left.
Move the right Direction Control right and the
ORBIT™ HD will bank to the right (see diagram I).
Move the left Throttle stick up to increase the
speed and the ORBIT™ HD will accelerate
and ascend.
Move the left Throttle stick down to decrease the
speed and the ORBIT™ HD will decelerate and
descend (see diagram F).
Move the left Throttle stick left and the
ORBIT™ HD will rotate left.
Move the left Throttle stick right and the
ORBIT™ HD will rotate right (see diagram G).
RECOGNIZING THE FRONT & BACK OF THE ORBIT™ HD
Even though the ORBIT™ HD has four rotors there is still a front or "forward" facing direction and "back" or
backwards facing direction. The front of the Quadrocopter displays WHITE LED lights and the back of the
Quadrocopter displays RED LED lights when activated (see diagram E).
ADJUSTING TRIM
From time to time you may have to adjust the TRIM buttons to ensure the ORBIT™ HD will hover in mid-air
and respond accurately to your commands (make all trim adjustments while the drone is in air).
G
NOTE:
You can still control the direction while auto starting/landing to avoid obstacles.
HOW TO START/STOP ROTORS
Make sure you have properly synced the ORBIT™ HD and the power stay on.
• To start the rotors simply move the two control sticks both down and all the way in the corners, hold until the rotors
starts spinning. Now release both sticks to the neutrall position and push the throttle up to take off.
• To stop the rotors right after start them,you can simply wait for about 10 seconds.They will stop automatically or
move both sticks down and all the way in the corners again to stop immediately.To stop the rotors after take off in the
air, you can simply pull the throttle all the way down to land and it will stop on the floor.
AUTO START/LAND BUTTON
The ORBIT™ HD has an auto start/land feature which allows you to start/land automatically. Simply press the
AUTO START / LAND
button on the top right of the controller and your ORBIT™ HD will begin taking off/Landing.(see diagram below)
