FRONT
REAR
B
A
A
B
U
9
10
ORBIT™ HD WARNING:
The ORBIT™ HD is designed for OUTDOOR use only. The ORBIT™ HD blades revolve at high speeds and can
cause damage to the user, spectators and animals. Stand away from the ORBIT™ HD to reduce the risk of
getting into the flight path. Warn spectators that you will be flying your ORBIT™ HD so that they are aware
of its position. Before flight, inspect the rotor blades to make certain that the blades are securely fastened
to the ORBIT™ HD.
WARNING!
• Choking/Cutting Hazard. Small Parts/Sharp Rotor Blades.
• Keep hands, hair and loose clothing away from the propeller when the power switch is turned to the
ON position.
• Turn off the transmitter and take out the battery from the ORBIT™ HD when not in use.
• The included charger is built specifically for the ORBIT™ HD Li-Poly battery. Do not use it to charge any
other battery.
• New alkaline batteries are recommended for maximum performance.
• Parental supervision recommended when flying ORBIT™ HD.
BATTERY WARNINGS
RECHARGEABLE BATTERY:
This ORBIT™ HD uses a Li-Poly rechargeable battery. If battery can no longer be charged, dispose it battery
properly according to the local law.
CONTROLLER BATTERIES:
Remote control requires 6 “AA” batteries (not included). Please read the important battery safety
warning below.
• Do not mix alkaline, standard (carbon-zinc) and rechargeable batteries (Nickel Metal Hydride).
• Do not mix old and new batteries.
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the item before being charged (if removable).
• Rechargeable batteries are only to be charged under adult supervision.
• Exhausted batteries should be removed immediately and must be recycled or disposed of properly
according to state or local government ordinances and regulations.
• The supply terminals are not to be short-circuited.
• Only batteries of the same or equivalent type as recommended are to be used.
• Batteries are to be inserted with the correct polarity (see inside booklet for diagram).
• Do not dispose batteries in a fire - batteries may leak or explode.
CARE AND MAINTENANCE
• Always remove the batteries from the wireless remote control when it is not being used for an
extended period of time.
• To clean, gently wipe the remote control and ORBIT™ HD with a clean damp cloth.
• Keep the toy away from direct heat or sunlight.
• Do not submerge the toy into water. This can damage the unit beyond repair.
• Parental guidance recommended when installing or replacing the batteries.
REPLACING THE PROPELLER BLADES
NOTE : Always disconnect the battery before replacing the propeller blades.
Your ORBIT™ HD propeller system is a precision instrument that may need repair or replacement from time
to time for optimal flight function. Crash landing from high-speed aerial flights may cause damage to your
ORBIT™ HD propellers.
The ORBIT™ HD has four propeller blades, two on the front and two on the back. Each one of these
propellers is marked with either A or B on the underside.
1. When replacing the propeller blades, carefully unscrew the broken propeller from the rotor shaft.
2. Replace the damaged blade with the correct new blade. Ensure that the identification letter on the
broken blade and on the new blade are the same before screwing back on (See diagram U).
NOTE : The Color of the blade does not matter. What matters is the identification letter on the
bottom of blade. All “A” blades would perform the same ir-respective of color and the same
would apply for “B” .
T
T1
T2
Camera Button
OPERATING THE CAMERA
You can take in-flight photos or video with your ORBIT™ HD on board camera.
1. Ensure that the camera module is securely attached and locked onto the copter. Insert the mircoSDHC
card carefully into the slot on the rear of the camera module. Push in gently until you hear and feel a click.
Now you are ready to use the camera.
2. To take still pictures, short press the camera button.The indicating LED light will flash 3 times.
3. To take video footage, hold down the camera button on the remote for a few seconds(see diagram T1).
To stop video footage simply press the button again.
4. After turning the Power Off on the copter, you may now remove the mircoSDHC card from the ORBIT™ HD by
gently pushing on the back of the card with your thumb until you hear and feel a slight click. You may use the
included USB card reader to connect it to a computer and retrieve your pictures and video footage.
