P11
1.
鎂合金片
2.
不織布
4.
下蓋
3.
上蓋
5
請沖洗以下零件並以手擦拭表面，確認沒有鹽分殘留。請個別乾燥。(請注意:如果鹽
分殘留在鎂合金片上將會使其使用壽命減短)
6
當玩具車速度開始變慢時，可加幾滴在圖示位置，請勿加到極性位置以免氧化。(請
注意 : 如果不織布已經乾掉，請拆開電池組並如第 之
C
圖所示增加鹽水，等待幾
分鐘不織布濕了就可以使用。
2
Bottom Base
Magnesium
Nonwoven Fabric
Cover
When the Baja Runner starts getting slow or stops, reapply a few drops into the position as
shown below. Please do not drop into the polarity of connectors to avoid oxidization.
(
Important:
If the fabric is totally dry, disassemble FC module and add salt water as per
figure
c
, or it will take few minutes to have the fabric wet completely.)
2
Flush below parts and hand rub the surface, make sure no salt residue. Dry all
parts separately. (
Important:
If salt is residual on the magnesium sheet, it will
shorten it’s life .)
P12
故 障 排 除
(新)
(已侵蝕須換新)
3
STEP
3
STEP
15
STEP
15
STEP
刮除這裡
刮除這裡
P9
鎂合金片
P1
端子
6
7
請確認馬達及軸承安裝順利沒有任何阻礙或卡住。(參考步驟 及步驟 )
當鎂合金片出現以下侵蝕狀況請更新。
請確認電池組是以正確的順序組裝，且放置位置正確 :
黑色空氣極 不織布 鎂合金片(參考步驟 )
請確認空氣極為黑色面朝上( 參考步驟 )
不織布用來隔絕空氣極及鎂合金片，請確認空氣極及鎂合金片沒有接觸
以免短路。(參考步驟 )
請確認電池組已完全的插入
。
(
參考步驟
)
鹽水容易形成氧化，在每次使用前可用一字起子，刮除端子及鎂合金片上的
氧化物。請參考下圖示實做。
18
STEP
18
STEP
16
STEP
16
STEP
16
STEP
16
STEP
16
STEP
1
2
3
4
5
16
STEP
Make sure FC module placed in correct sequence and position:
air cathode →nonwoven fabric →magnesium sheet. (Ref: )
Nonwoven fabric is also used to isolate air cathode and magnesium sheet, make sure
the 2 parts do not come into contact each other or it may cause short circuit. (Ref: )
Salt water will easily cause oxidization, scratch oxide from the battery connectors
and also magnesium sheet by slotted screwdriver before reuse. See below figures:
Make sure FC module is inserted entirely. (Ref: )
Make sure air cathode black side face up. (Ref: )
(New)
(Need to replace)
Scratch Here
Scratch Here
P9 Magnesium Sheet
P1 Connector
Trouble Shooting
Make sure motor and shaft are installed smoothly without any barriers. (Ref: , )
Replace a new magnesium sheet if it is eroded as shown below.
