background image

OPERATING INSTRUCTIONS 

 

CAUTION! 

When making voltage or current measurements, develop the 
habit of turning off all power to the circuit under test. Connect the 
test leads at the desired points in the circuit, and then turn on 
the power while taking readings. Turn off the power before 
disconnecting the test leads from the circuit. 
 

INTERNAL BATTERY CHECK 

To check the battery condition, insert the black test lead into the 

(-) jack. Set the range switch to the R X1 range position and 
short the ends of the two sides of the test leads. If the pointer 
can not be brought to the zero mark, replace the 1.5V cells or 9V 
cell. (See battery replacement.)   

 
BEFORE OPERATING 

1. Set the range switch to the proper position before making any 

measurement. 

2. Never apply more voltage or current than the rated value in 

every position. 

3. When the voltage or current to be measured it not known, 

always start with the highest range. 

4. If meter indication is in the lower half of the scale and falls 

within the range of a lower scale, reset selector switch to the 
lower range for greatest accuracy. 

5. If the meter won’t work at all, check the fuse located on the 

PCB. If it’s blown, replace it. (See fuse replacement.) 

6. Avoid placing the meter where extreme shock or continuous 

vibration is encountered and do not store in excessively hot or 
damp places. Although very rugged, the meter is a sensitive 
measuring device and should be handled carefully & properly. 

7. Do not check resistance, transistor, diode, LED, or 

capacitance when live voltage or current input across the 
circuit. 

8. When the meter is not in use, keep the selector switch to the 

 

Summary of Contents for mt-2017

































Reviews: