ProLinx-HART ♦ ProLinx Gateway
Index
HART Master with Analog I/O
Driver Manual
ProSoft Technology, Inc.
Page 103 of 104
October 13, 2011
Index
[
[Analog HART Card x]
• 28
[HART PORT x COMMANDS]
• 31
[HART PORT x]
• 29
A
Agency Approvals and Certifications
• 4
Allocation of Risks
• 102
Auto-Poll Code
• 30
Auto-Poll DB Address
• 30
Auto-Poll Disabled Mode
• 24
Auto-Poll Swap Float
• 30
Auto-Polling
• 21
B
Burst Mode
• 21
Byte Count
• 35
C
CHx High
• 28
CHx Low
• 28
COMMAND 00 - Read Unique Identifier
• 42
COMMAND 01 - Read Primary Variable
• 43
COMMAND 02 - Read Current And Percent
Of Range
• 44
COMMAND 03 - Read Dynamic Variables
•
45
COMMAND 06 - Write Polling Address
• 46
COMMAND 108 - Write Burst Mode
Command Number
• 82
COMMAND 109 - Burst Mode Control
• 83
COMMAND 110 - Read All Dynamic
Variables
• 84
COMMAND 12 - Read Message
• 47
COMMAND 13 - Read Tag, Descriptor and
Date
• 48
COMMAND 14 - Read PV Sensor Info
• 49
COMMAND 15 - Read Output Information
•
50
COMMAND 16 - Read Final Assembly
Number
• 51
COMMAND 17 - Write Message
• 52
COMMAND 18 - Write Tag, Descriptor and
Date
• 53
COMMAND 19 - Write Final Assembly
Number
• 54
COMMAND 33 - Read Transmitter Variables
• 55
COMMAND 34 - Write Damping Value
• 56
COMMAND 35 - Write Range Values
• 57
COMMAND 36 - Set Upper Range Value
• 58
COMMAND 37 - Set Lower Range Value
• 59
COMMAND 38 - Reset Configuration
Changed Flag
• 60
COMMAND 39 - EEPROM Control
• 61
COMMAND 40 - Enter Exit Fixed Current
Mode
• 62
COMMAND 41 - Perform Transmitter Self
Test
• 63
COMMAND 42 - Perform Master Reset
• 64
COMMAND 43 - Set PV Zero
• 65
COMMAND 44 - Write PV Units
• 66
COMMAND 45 - Trim DAC Zero
• 67
COMMAND 46 - Trim DAC Gain
• 68
COMMAND 47 - Write Transfer Function
• 69
COMMAND 48 - Read Additional Transmitter
Status
• 70
COMMAND 49 - Write PV Sensor Serial
Number
• 71
COMMAND 50 - Read Dynamic Variable
Assignments
• 72
COMMAND 51 - Write Dynamic Variable
Assignments
• 73
COMMAND 52 - Set Transmitter Variable
Zero
• 74
COMMAND 53 - Write Transmitter Variable
Units
• 75
COMMAND 54 - Read Transmitter Variable
Information
• 76
COMMAND 55 - Write Transmitter Variable
Damping Value
• 77
COMMAND 56 - Write Transmitter Variable
Sensor Serial Number
• 78
COMMAND 57 - Read Unit Tag Descriptor
Date
• 79
COMMAND 58 - Write Unit Tag Descriptor
Date
• 80
COMMAND 59 - Write Number Of Response
Preambles
• 81
Command Count
• 30
Command List Overview
• 31
Connecting Power to the Unit
• 13
Connections for HART Analog Point-to-Point
Devices
• 90
Contacting Technical Support
• 95, 97
Controlling Law and Severability
• 102
D
Database Register
• 28
DB Address Status
• 29
Delay Preset
• 39
Disclaimer of all Other Warranties
• 101
Disclaimer Regarding High Risk Activities
•
100
Done DB Address
• 35
Downloading a File from PC to the Module
•
40
E
Enable
• 32
Enable DB Address
• 35