background image

© 2014 Prostage SL

Page 10

8  

Declaration of Conformity 

Company: 

Prostage SL

 

Apdo 57

 

ES-07560 Cala Millor

Type of equipment:  PurpleLine System

Trademarks:  

Prostage / StageWire

Models: 

XDS, XLS, XTMpro, X10, X07, X05, X01, XB1

The products meet the requirements of the following standards:

EMC: 

EN 55103-2 | EN 55103-1:2009 | EN 55103-2:2009

 

EN 61000-3-2

 

EN 61000-4-2 | EN 61000-4-3 | EN 61000-4-4 | EN 61000-4-5 | EN 61000-4-3 | EN 61000-4-11

Safety: 

IEC 60065:2001 | EN 60065:2002 / A1:2006 / Cor.:2007 / A11:2008 

Year: 2011

Cala Millor, 14. Dezember 2011  Lukas Truninger, CEO

Information to the user: 
 

Class B Statement:

 

 
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a 
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio communications. However, 
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause 
harmful interference to radio or television reception, which can be determined by turning the equipment off and 
on, the user is encouraged to try to correct the interference by one or more of the following measures: 
- Reorient or relocate the receiving antenna. 
- Increase the separation between the equipment and receiver. 
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 
- Consult the dealer or an experienced radio/TV technician for help. 

Summary of Contents for X07











Reviews: