background image

M10 self-locking nuts

(DIN 985)

M10 bolts

(DIN 933)

M10 washers

(DIN 125A)

 

10 

 10 

 45 

Device in a vertical position

energy absorber

Device in a horizontal position

energy absorber

POSITIONING OF THE DEVICE

Check the proper position of the device and correct guiding of the rope shown on the pictures below.

1.

The construction element where the winch is installed must be vertical or horizontal.

2.

Attach the energy absorber to the cable using the connector supplied with the absorber.

3.

Connect absorber's connector to the attachment element of a harness. Use "A" frontal or dorsal attachment point in full body 

4.

harness (EN 361) or rescue attachment point in rescue harness (EN 1497) or rescue loops (EN 1498).

INSTALLING ON THE STEEL PROFILE

To the narrow structural elements the winch should be installed using two holes ( 10 mm and oblong  10x45) situated on 

1.

the back wall of the winch.

Device should be installed using two M10 steel bolts. Put the bolts through the back wall of the winch and through the 

2.

structural anchor profile. 

Put the washers M10 (DIN 125A) under the head of each bolt and under each nut. Tighten two M10 self-locking nuts (DIN 

3.

985).

4/8

Summary of Contents for AT 050 Series









Reviews: