The device can be used for 10 years from the manufacturing date.
NOTE: Maximum time of usage depends on intensity and environment of use. If the device is used in heavy conditions,
being exposed to frequent contact with water, sharp edges, extreme of temperatures or exposed to corrosive
substances, it may be necessary to withdraw the device after only one use.
K. WITHDRAWAL FROM USE
The device must be withdrawn from use immediately and destroyed if it has been used to arrest a fall, or failed a
periodic inspection or there are any doubts concerning its function.
L.
ESSENTIAL PRINCIPLES FOR USE OF PERSONAL FALL PROTECTION EQUIPMENT
personal fall protection equipment should be used only by personnel trained in its use.
personal fall protection equipment must not be used by a person with medical condition that could affect safety of the
equipment user in normal and emergency use.
develop a rescue plan to be implemented during operation whenever necessary.
being suspended in personal fall protection equipment (e.g. after arresting a fall) please note symptoms of suspension
trauma.
to avoid negative effects of suspension make sure a corresponding rescue action plan is prepared. It is recommended to
use support tapes.
it is forbidden to make any alterations or additions to the equipment without prior written consent given by the
manufacturer.
any repair shall only be carried out by manufacturer of the equipment or an authorised representative.
personal fall protection equipment shall not be used for any purpose other than intended.
personal fall protection equipment provides individual protection and shall be used by one person only.
before each use make sure that all parts of fall protection system cooperate correctly. Periodically examine connections
and fitting of components of the equipment to prevent any accidental loosening or disconnection.
it is forbidden to use a combination of the equipment where function of any one component is affected by, or interferes
with the function of any other.
before each use of personal fall protection equipment carry out a detailed inspection to ensure that the device is
operable and operates correctly.
in particular, before use inspect all accessible elements of the equipment for any damages, excessive wear, corrosion,
abrasion, cutting or improper function. For individual devices pay particular attention to:
-
in full body harnesses, sit harnesses and work positioning devices: buckles, regulating elements, attachment
points (buckles), webbing, seams, belt loops;
-
in energy absorbers: attachment loops, webbing, seams, housing, connectors;
-
in lanyards and textile guides: rope, loops, thimbles, connectors, regulating parts, splices;
-
in lanyards and steel guides: rope, wires, clamps, loops, thimbles, connectors, regulating parts;
-
in retractable type fall arresters: lanyard or webbing, retractor and locking mechanism for proper operation,
housing, energy absorber, connectors;
-
in guided type fall arresters: body, proper guiding, locking mechanism for proper operation, rollers, bolts and
rivets, connectors, energy absorber;
-
in metal parts (connectors, hooks, snap hooks): load-bearing body, rivets, main pawl, function of locking gear.
at least once a year, after each 12 months of use, personal fall protection equipment must be withdrawn from use to
carry out periodic detailed inspection. Periodic inspection can be carried out by a properly qualified and skilled person.
Also periodic inspection can be carried by manufacturer of the equipment or his authorized representative.
in some cases, if fall protection equipment has a complex design (e.g. fall arresters), periodic inspections can be carried
out by manufacturer of the equipment, or his authorized representative only. After the periodic inspection, date of the
next inspection should be marked.
regular periodic inspections are essential in respect of the equipment condition and safety of users which is dependent
on functionality and durability of the equipment.
during periodic inspection it is necessary to check the legibility of all markings on the equipment (identity label of the
device). Do not use the equipment if marking is illegible.
It is essential for the user's safety that the product is re-sold outside the original country of destination the reseller must
provide instructions for use, for maintenance, for periodic inspection and for repair in language of the country where the
product is to be used.
Personal fall protection equipment must be withdrawn from use and discarded immediately (or other procedures based
on instruction manual should be applied) if it has been used to arrest a fall.
full body harness compliant with EN 361 is the only device supporting user's body in fall arrest systems.
fall arrest system can be connected to attachment points (buckles, loops) on full body harness marked with capital letter
“A”
anchor point (device) of the fall protection equipment should have a stable structure and position so as to prevent a
possibility of the load fall and minimize a free fall distance. Anchor point of the equipment should be located above the
user's work station. The shape and construction of the anchor point shall not allow for a self-acting disconnection of the
equipment. Minimum strength of anchor point of the equipment should be 12kN. It is recommended to use certified and
marked anchor points of the equipment compliant with EN 795.
it is obligatory to verify the free space required under the user at workplace before each occasion of using the fall
protection system, so that, in case of a fall, there is no collision with the ground or other obstacle in the fall path. The
required free space should be determined on basis of the data given in the instruction manual of the equipment to be
used.
When using the equipment, inspect it on a regular basis, paying special attention to risks and damages affecting
operation of the equipment and the user's safety, and in particular to kinks and rope movement on sharp edges,
oscillatory falls, electrical conductivity, any damages such as cuts, abrasions, corrosion, influence of extreme
temperatures, negative influence of environmental factors, chemical substances.
personal fall protection equipment must be transported in a package (e.g.: bag made of moisture-proof textile or foil bag
or cases made of steel or plastic) to protect it against damage or moisture.
personal fall protection equipment should be cleaned without causing adverse effect on the materials used in the
production of the equipment. For textile materials (webbings, ropes) use agents suitable for delicate fabrics. Can be
washed in hands or in a washing machine. Rinse thoroughly. Clean energy absorbers using damp cloth only. Do not
immerse energy absorber in water. Wash textile products with water only. When the equipment becomes wet, either
from being in use or after cleaning, allow it to dry naturally, and keep it away from sources of heat. In metallic products
lubricate slightly some mechanical parts (springs, hinges, pawls, etc.) regularly to ensure their better operation.
personal fall protection equipment should be stored loosely packed in well-ventilated rooms, protected from direct light,
UV degradation, dust, sharp edges, extreme temperatures and aggressive chemical substances.
all parts of personal fall protection equipment must conform to instruction manuals for the equipment and standards in
force:
- EN 353-1, EN 353-2, EN 354, EN 355, EN 360 - for fall arrest systems;
- EN 362 - for connectors
- EN341, EN1496, EN1497, EN1498 - for rescue equipment
- EN 361 - for full body harnesses;
- EN 813 - for sit harnesses;
- EN 358 - for work positioning systems;
- EN 795 - for anchor devices.
Manufacturer:
PROTEKT - Starorudzka 9 - 93-403 Łódź - Poland
tel. +4842 6802083 - fax. +4842 6802093 - www.protekt.com.pl
Notified body responsible for EU type test certification in accordance with Regulation 2016/425:
PRS - No.1463, Polski Rejestr Statków S.A. al. gen.
Józefa Hallera 126 80-416 Gdańsk, Poland,
Notified body responsible for supervision of manufacturing of the equipment:
APAVE SUD EUROPE SAS (no 0082) - CS 60193 - F13322 MARSEILLE CEDEX
IDENTITY CARD
SERIAL
/BATCH
NUMBER
It is the responsibility of the user organisation to provide the identity card and to fill in the
details required.
The identity card should be filled in before the first use by a competent
person, responsible inthe user organization for protective equipment.
Any information
about the equipment like periodic inspections, repairs, reasons of equipment's withdra
wal
from use shall be noted into the identity card by a competent person
in the user
organization.
The identity card should be stor
ed
during a whole period of equipment
utilization.
Do not use the equipment without the identity card.
MODEL AND TYPE OF EQUIPMENT
PERIODIC
INSPECTION
AND REPAIR HISTORY
CARD
REFERENCE
NUMBER
DATE OF
MANUFACTURE
DATE OF
FIRST USE
DATE OF PURCHASE
NEXT
INSPECTION
DATE
DATE OF
INSPECTION
REASON FOR
INSPECTION
OR REPAIR
DEFECTS
,
CONDITION
NOTED
REPAIRS CARRIED OUT
NAME AND SIGNATURE
OF COMPETENT
PERSON
USER NAME
