41
Error Message Details
错误信息详情
In the event that you get an error message, the Radius will alert you on screen as to the reason for the
error and the suggested fix. Below is a list of the error messages that can occur.
如果您得到一个错误信息，
Radius
会在屏幕上提醒您错误的原因和修复建。以下是可能发生的错误信息列
表。
Check Battery, Contacts and Spring
- This can happen if you are using a bad battery or the spring is
not making a good connection with the battery. This can usually be fixed by removing the end cap and
adjusting your spring, checking that all your contacts are clean and then reinstalling the end plate.
检查电池，接触和弹簧
-
如果您使用的是坏电池或与弹簧的接触不好就可能会发生这种情况。通常情况下
打开后盖、调整弹簧，确保所有的接触点是干净的，然后盖上后盖就可以解决这个问题。
Reduce Watts or Change Atomizer
-
If the atomizer ohms are too high or your output wattage is set too
high this error can occur. Try lowering the power level or change your atomizer.
降低瓦数或更换雾化器
-
如果雾化器欧姆数过高或输出功率设置得太高就可能会出现此错误。可以尝试降
低功率或更换雾化器。
Increase Watts or Change Atomizer
- There are situations where you need to increase the watts. For
example, if you set the device to 3 watts and try to use a low resistance atomizer, the device cannot drive
power at that level. This scenario will prompt this error.
增加瓦特数或更换雾化器
-
有时候需要增加瓦特数。例如，如果您将设备调到到
3
瓦并使用低电阻雾化器，
设备则不能在这个水平下正常工作。这种情况下这种错误就会发生。
Reduce Watts or Replace Atomizer
– This error can occur if the wattage is set too high and Radius
cannot safely power the atomizer with your current settings. This can also happen if you have the wattage
set too high along with the boost mode set too high. Try lowering your settings. Most of the time, if you
have these power settings too high, you will be burning the juice and it won’t taste very good or you risk
burning out your atomizer.
降低电压
/
瓦特数或更换雾化器
-
如果电压或功率设置过高，
Radius
不能安全地给雾化器供电，就会发生这
种错误。如果功率设置过高同时增强模式设置过高也会导致这个问题。可以尝试着降低您的设置。大多数
时候情况下如果电源设置得太高，您就是在燃烧烟油并且味道也不会很好，或者有烧坏雾化器的风险
Replace Atomizer and Try Again
– This can happen if the resistance of your atomizer is too low or has
failed. Anytime the resistance of your atomizer drops, in most cases, it has burned up or failed. This can
also occur if you make your own coil on a RBA and you go below the resistance level that is safe.
Typically this is anything below .3 ohms. Try installing a new atomizer and see if the problem goes away.
更换雾化器后再试
-
如果雾化器的电阻过低或出现故障会出现这个问题。雾化器电阻下降多数情况下是因
为烧坏或出现故障。如果您用
RBA
自己制作线圈并且低于安全电阻，如低于
0.3
欧姆，也会发生这样的问
题。尝试安装新的雾化器，看看问题是否会消失。
Let Cool and Replace Battery
– While these are very rare error messages, the system is monitoring for
an unsafe condition with your battery. If your battery ever gets too hot and it’s not safe to use, carefully
remove the battery and properly discard. If the unit is too hot, it’s best to set it down and wait for it to cool
off before removing the cell. Anytime you have a battery fail, always discard the cell and replace it with a
new one. Never try to recharge or reuse a bad battery. Also remember to always use the correct batteries
in the Radius.
降温并更换电池
-
这些错误信息非常少见，系统一直在监测电池的不安全状态。如果电池变得太热不能安
全地使用，要小心地取出电池并妥善处理掉。如果设备太热了，最好是让它安定下来并等待它降温，然后
