background image

Zones

Heating and Cooling Stages

Rev G Aug 2015

Bypass Control

Optional Sensors

Panel Power

Warranty

Wiring

Humidity Rating

Temperature Ratings

Dampers per Zone

Compatible Equipment

Equipment Selection

The panel can be used with traditional mechanical barometric 
dampers,  adjusting the close position limit on each zone 
damper or use the non-calling zone dampers for bypass.

Discharge air (Model TS2) and outdoor air temperature sensor 
(Model TS3) can be used.  A pressure sensor (Model PS2) can 
be used to monitor duct pressure.

24VAC (18 to 30), 10VA

5-year warranty limited to repair or replacement of panel due to 
defective material or workmanship.

Use 18 or 20 AWG solid thermostat wire.

5 to 90% RH non-condensing.

Shipping

o

o

o

o

-20  to 150 F (-29  to 66 C)

o

o

o

o

0  to 165 F (-32  to 74 C)

Operating

Multiple dampers may be used to configure a zone.  The total 
number of dampers that can be used depends on the VA  
rating of the 24VAC transformer used.  Up to six dampers can 
be daisy chained to configure a zone.

All panels operate with gas/electric systems, conventional heat 
pumps and dual fuel heat pumps.

Selected using the jumper plugs on the panel.  See table 
below.

See table below.

See table below.

HVAC

PANEL

ZONE DAMPERS

1

1

2

2

3

Fresh

Air

3

 THERMOSTATS

Q

u

ic

V

ie

w

Zoning Panel

ProZone

7-5/8 (193)

9-5/8 (244)

1-5/8 (41)

Compatible Dampers

The ProR80J-XX dampers with plug and play cables.  Each 
damper is supplied with a 25-foot cable.  

Compatible Thermostats

Compatible Thermostat Types

When gas/electric equipment is selected, heat/cool thermostats 
are used in all zones.  When heat pump equipment is selected, 
a heat pump or heat/cool thermostat may be used in Zone1  
and heat/cool thermostats are used in all other zones.

Single stage, 24VAC powered or battery powered thermostats.

Zone

Pro

I n t e l l i g e n t  Z o n i n g

Installation Guide

ProR221J, ProR212J, ProR321J  and ProR312J

Zones on Panel

Two

Two

No

No

Two

One

One

Two

One

Two

One

None

One

None

Two

One

One

One

Two

Two

No.

No.

Three

Three

Model ProR221J

Model ProR212J

Model ProR321J

Model ProR312J

Expandable

Heating Stages

Compressor Stages

Cooling Stages

Auxiliary Heating Stages

Gas/Electric Equipment

Heat Pump Equipment

Summary of Contents for ProR212J

















Reviews: