background image

Building your MINI+

Original Prusa MINI+ semi-assembled

13

STEP 13

 Joining the parts together - preparation

Locate the Y-axis motor cable placed in the extrusion and pull it out carefully.
Take the rubber band off from the cable, guide the cable below the extrusion and

out (see the picture).
Move the heatbed all the way to the right.
Place the right M3nE nut approximately in the middle of the extrusion's length, but

make sure it is not under the heatbed structure.

STEP 14

 Protecting the LCD cable

WARNING

: From now on proceed carefully while moving the XZ-axis. The LCD

cable is facing down and might get damaged.

In order to protect the cable, please follow the instructions below. Also, don't try any

other orientation, because it will complicate the assembly.
Carefully lay the XZ-axis on its side (see the picture) and start wrapping the LCD

cable around the box. Don't stretch the cable.
Now, tilt the axis back to get better access inside the electronics box and gently

insert the cable in. Make a loop under the power button cables. Note, that this is

only a temporary solution.

Summary of Contents for MINI+

































Reviews: