background image

SAFETY CHECK LIST

1.

Before operating the compressor, ensure the vessel to which the

compressor is connected is certified to withstand the pressure and
/or vacuum produced.

2.

Verify adequately sized relief valves have been fitted to protect the

vessel. Do not use solvents or inflammable products for cleaning
the pipelines and the accessories.

3.

Gas/air mixtures which are potentially volatile/explosive must not be

introduced or allowed to be introduced into the compressor.

4. 

All pressure vessel and piping connected to the compressor must

be isolated and in a safe operating condition.

5.

Operators should wear ear protection when operating truck mount-
ed compressors.

6.

There are components within the compressor of sufficient weight

to cause injury if mishandled. Use proper lifting devices as neces-
sary.

7.

Where necessary, this equipment should be grounded to control

static electricity.

8. 

The temperature of the air leaving the compressor is elevated

above ambient due to air compression. Check that the elevated
temperatures do not adversely affect the product and any material
used in design of the system. Attach clearly marked warning signs
to warn of potentially hot surfaces on the compressor, piping and
accessories which will burn if touched.

9.

Mounting of the compressor must be correctly engineered and the

compressor must be properly secured. Refer to the Compressor
Mounting section of this manual.

NOTICE :

MOUVEX COMPRESSORS ARE DESIGNED TO PRODUCE COM-
PRESSED AIR. NOT TO PUMP LIQUIDS, LIQUEFIED GASSES OR
POWDERS THOUGH THE COMPRESSOR. TO DO SO WOULD VOID
THE WARRANTY.

LIFTING POINTS :

The compressor can be picked up from underneath to be
transported.

Discharge flanges threads can be used to install a lifting lug
in order to transport the compressor.

WARNING

IT IS IMPERATIVE TO APPLY THE
TRUCK PARKING BRAKE AND TO
BLOCK THE WHEELS BEFORE ANY
INTERVENTION DUE TO RISKS OF
SERIOUS BODILY INJURIES OR PRO-
PERTY DAMAGE.

Hazardous machinery 

can cause severe

personal injury or 

property damage.

WARNING

COMPRESSING GASES INTO A VES-
SEL CONTAINING FLAMMABLE OR
EXPLOSIVE GASES OR COMPRESSING
FLAMMABLE OR EXPLOSIVE GASES,
CAN CAUSE PROPERTY DAMAGE,
PERSONAL INJURY OR DEATH.

Hazardous fluids 

can cause fire, 

serious personal injury

or property damage.

WARNING

FAILURE TO INSTALL ADEQUATELY
SIZED PRESSURE RELIEF VALVE(S)
CAN CAUSE PROPERTY DAMAGE,
PERSONAL INJURY OR DEATH.

Hazardous pressure 

can cause 

personal injury 

or property damage.

CAUTION

COMPRESSOR, PIPING AND ACCES-
SORIES WILL BECOME HOT DURING
OPERATION AND CAN CAUSE SERIOUS
PERSONAL INJURY.

Extreme heat can 

cause injury or

property damage.

WARNING

CONTENTS OF THE COMPRESSOR,
TANK,  PIPING, AND FILTERS COULD
BE HAZARDOUS TO HEALTH.
TAKE ALL NECESSARY PRECAUTIONS
WHEN PERFORMING COMPRESSOR
SERVICE OR MAINTENANCE.

Hazardous or toxic

fluids can cause 

serious injury.

WARNING

THE NOISE EMITTED BY WORKING
MOUVEX SCREW COMPRESSOR
CAN BE HIGHER THAN 80 DBA.
THE END USERS MUST USE, WHEN
NECESSARY THE APPROPRIATE
EAR PROTECTIONS. FAILURE TO
WEAR HEAR PROTECTIONS IN
AREAS WHERE THE NOISE IS
HIGHER THAN 80 DBA CAN LEAD TO
PERMANENT BODY DAMAGE.

A loud noise can

cause permanent

body damage.

3/22

NT 1401-X00 10 18 B200 Flow Control  e

SAFETY DATA

Summary of Contents for Mouvex B200 Flow Control























Reviews: