background image

 

 

40

PSG LIMITED LIFETIME WARRANTY 

 

The  warranty of the manufacturer extends only to the original consumer purchaser and is not transferable. This warranty covers 
brand new products only, which have not been altered, modified nor repaired since shipment from factory. Proof of purchase (dated 
bill of sale), model name and serial number must be supplied when making any warranty claim to your PSG dealer.   

This warranty applies to normal residential use only.  Damages caused by misuse, abuse, improper installation, lack of 
maintenance, over firing, negligence or accident during transportation are not covered by this warranty. 

This warranty does not cover any scratch, corrosion, warping, or discoloration caused by over firing, abrasives or chemical cleaners. 
Any defect or damage caused by the use of unauthorized parts or others than original parts void this warranty. An authorized 
qualified technician must perform the installation in accordance with the instructions supplied with this product and all local and 
national building codes. Any service call related to an improper installation is not covered by this warranty. 
The manufacturer may require that defective products be returned or that digital pictures be provided to support the claim. Returned 
products are to be shipped prepaid to the manufacturer for investigation. If a product is found to be defective, the manufacturer will 
repair or replace such defect and reasonable transportation fees will be refunded. Repair work covered by the warranty, executed at 
the purchaser’s domicile by an authorized qualified technician requires the prior approval of  the manufacturer. Labour cost and 
repair work to the account of the manufacturer are based on predetermined rate schedule and must not exceed the wholesale price of 
the replacement part. All labour and  freight costs covered by this warranty are  limited according to the table below.   
The manufacturer at its discretion may decide to repair or replace any part or unit after inspection and investigation of the defect. The 
manufacturer may, at its discretion, fully discharge all obligations with respect to this warranty by refunding the wholesale price of 
any warranted but defective parts The manufacturer shall in no event be responsible for any special, indirect, consequential damages 
of any nature, which are in excess of the original purchase price of the product. 

 

DESCRIPTION 

WARRANTY APPLICATION 

PARTS LABOUR 

Combustion chamber (welds only) and castings 

Lifetime 

5 years 

Plating (defective manufacture) – subject to limitations above 

Lifetime 

n/a 

Secondary air tubes, vermiculite baffle, C-Cast baffle and  handle 

assembly 

5 years 

n/a 

Stainless steel baffle and parts 

5 years 

3 years 

Carbon steel baffle and parts 

2 years 

1 year 

Oil burner, electrical elements, blowers, thermal switches, rheostat, 

relays, damper motor, fan & limit, and other controls 

2 years 

1 year 

Paint (peeling), gaskets, insulation, and ceramic glass (thermal 

breakage only*) 

1 year 

n/a 

*Pictures required 
 

Shall your unit or a components be defective, contact immediately your PSG dealer. Prior to your call make sure you have 

the following information necessary to your warranty claim treatment: 

 

 

Your name, address and telephone 
number;  

 

Bill of sale and dealer’s name; 

 

Serial number and model name as indicated on 
the nameplate fixed to the back of your unit; 

 

Nature of the defect and any relevant 

information. 

 

Before shipping your unit or defective component to our plant, you must obtain from 

your PSG dealer an Authorization Number. Any merchandise shipped to our plant 

without authorization will be refused automatically and returned to sender. 

Summary of Contents for PSG-2000









































Reviews: