PSI Waste Equipment Services, Inc.
P50 Apartment Compactor
Sec
Ɵ
on 3, Opera
Ɵ
on
10
Fault Condi
Ɵ
ons
Solid
Light
on
E
‐
STOP
The
photo
eye
is
blocked.
Clean
the
photo
eye
and
make
sure
it
is
properly
aligned.
Press
E
‐
STOP
and
pull
it
back
out.
Press
START.
Flashing
light
on
E
‐
STOP
Call
quali
fi
ed
compactor
repair
technician.
Download
repair
manual
for
list
of
possible
causes.
Once
re
‐
solved
press
E
‐
STOP
and
pull
it
back
out.
Press
START.
Solid
AMBER
LIGHT
The
compactor
is
full.
Make
sure
the
ram
is
in
the
fully
back
posi on.
Change
out
the
container.
Press
START.
KEY
SWITCH
is
in
AUTO,
warning
light
is
not
on,
compactor
is
not
running
The
cycle
was
interrupted.
Make
sure
all
doors
are
closed
and
E
‐
STOP
is
pulled
out.
Press
START.
Sleep
Mode
If
“Sleep
Mode”
is
used
the
compactor
will
not
operate
in
AUTO
during
this
me.
“Sleep
Mode”
will
ap
‐
pear
on
the
status
screen.
This
prevents
the
compactor
from
running
automa cally
late
at
night
and
dis
‐
turbing
residents.
The
compactor
can
s ll
be
operated
using
the
START
bu on.
Once
the
compactor
“wakes
up”
it
will
resume
normal
opera on.
See
se ngs
below
for
more
informa on.
Danger:
Only
quali
fi
ed
and
authorized
personnel
should
a empt
the
following!
To
use
“Sleep
Mode”
you’ll
have
to
set
the
clock
on
the
Versa
‐
Pak
system
and
then
the
mers
to
tell
the
Versa
‐
Pak
system
when
to
turn
the
automa c
opera on
ON
and
OFF.
See
page
12
for
a
view
of
the
screen.
Set
the
clock
by
pressing
[OK
1]
[2
]
[2
]
[2
]
to
SET
CLOCK.
Press
[OK
1]
[OK
1].
You
are
now
on
the
date/ me.
Date
is
arranged
YY/MM/DD.
Time
is
in
24hrs.
So
1pm
would
be
13:00.
The
date/ me
are
all
one
fi
eld
and
are
changed
at
the
same
me.
Press
[OK
1].
Use
[3
]
and
[4
]
to
scroll
between
date
and
me.
Use
[5
]
and
[2
]
to
change
the
values.
Con
fi
rm
the
date
and
me
are
correct.
Press
[OK
1]
[OK
1].
Now
you
need
to
set
the
sleep
mode
mer.
This
me
is
also
in
24
hrs.
So
11:00
pm
would
be
23:00.
Press
[ESC
0]
[5
].
You
should
now
be
on
PARAMETER.
Press
[OK
1]
[OK
1]
[3
].
You
should
now
be
on
the
T
of
T0.
The
T
should
be
blinking
o
ff
and
on.
Press
[2
].
You
should
now
be
on
“@0”.
Press
[OK
1]
[2
]
[2
].
You
should
now
be
on
“ON
00:00”.
The
is
the
me
the
compactor
“wakes
up”
in
the
morning.
Press
[OK
1].
Use
[5
]
and
[2
]
to
change
the
values
and
[3
]
and
[4
]
to
scroll
between
MM
and
HH.
When
the
ON
me
is
set,
press
[OK
1].
Use
[2
]
to
go
to
the
OFF
me.
Press
[OK
1].
This
is
the
me
the
compactor
“goes
to
sleep”.
