background image

 

                          

WEEE designation  

 

The waste electric and  electronic  equipment worn  out  may not  be disposed of together 
with  standard  household  waste.  According  to  the  WEEE  directive,  applicable  in  the  EU, 
the  separate  neutralization  methods  should  be  used  for  electric  and  electronic 
equipment

 

 

 
 
 
 
 
 

 

 

 

 
 
 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

Pulsar K.Bogusz Sp.j.  

Siedlec 150,  32-744 Łapczyca, Poland 

Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50 

e-mail: 

biuro@pulsar.pl

sales@pulsar.pl

 

http:// 

www.pulsar.pl

 

 

GENERAL WARRANTY CONDITIONS 

 

1. Pulsar K. Bogusz Sp.j. (manufacturer) grants a two-year quality warranty for the equipment, starting from the date of purchase 
placed on the purchase order.  
2. Should such purchase order be missing when the claim is submitted, the three-year guarantee period is counted from the date 
of the manufacturing of the device.  
3. The warranty includes free-of-charge repairing or replacing with a functional equivalent (the selection is made by the 
manufacturer) of the malfunctioning device, due to reasons attributable to the manufacturer, including manufacturing and material 
defects, unless such defects have been reported beyond the warranty period (item 1 and 2).  
4. The equipment subject to warranty is to be brought to the place where it was purchased, or directly to the main office of the 
manufacturer.  
5. The warranty applies to complete equipment, including the type of defect specified in writing, using a properly filled warranty 
claim.   
6. Should the claim be accepted, the manufacturer is obliged to render warranty repairs, as soon as possible, however not later 
that within 14 days from the delivering of the equipment to the service centre of the manufacturer.  
7. The repair period mentioned in item 6 may be prolonged, if there is no technical capability to carry out the repairs, and in the 
case that the equipment has been accepted conditionally, due to the failing of the warranty terms by the claimant.  
8. All the services rendered by force of the warranty are carried out at the service centre of the manufacturer, exclusively.  
9. The warranty does not cover the defects of the equipment, resulting from: 
- reasons beyond the manufacturer's control, 
- mechanical damage, 
- improper storage and transport, 
- use that violates the operation manual or equipment application,  
- random events, including lightning discharges, failures of power networks, fire, flooding, high temperatures and chemical agents,  
- improper installation and configuration (at variance with the rules set forth in the manual), 
10. Each confirmation of structural modifications or repairs, carried out beyond the service centre of the manufacturer, or any 
modification of serial numbers or warranty labels, results in the loss of the rights resulting from the warranty. 
11. The liability of the manufacturer towards the buyer is limited to the value of the equipment, determined according to the 
wholesale prices suggested by the manufacturer on the day of purchase.  
12. The manufacturer shall not be responsible for the defects that resulted from the damaging, malfunctioning or inability to 
operate the equipment, particularly, if such defects are the result of failing to abide by the recommendations and requirements 
contained in the manual, or the use of the equipment.  

 

Summary of Contents for PSB1002435

Page 1: ...y supply occurs The power supply has the following protections short circuit SCP overload OLP and overvoltage OVP 1 2 Technical parameters Supply voltage 176 264V AC 50 60Hz Current consumption 0 90A 230VAC max Supply power 100W max Efficiency 83 Output voltage 27 6V DC buffer operation 19V 27 6V DC battery operation Output current 3A 0 5A battery charging 2 5A 1A battery charging Output current t...

Page 2: ...idity RH 90 max without condensation and the temperature within the range from 10 C to 40 C The power supply shall be mounted in a close casing a cubicle a terminal device and in order to fulfill LVD and EMC requirements the rules for power supply encasing and shielding shall be observed according to application Due to the power supply design the PE wire has to be connected to the corresponding co...

Page 3: ... of AC voltage ADJ Potentiometer output voltage adjust I1 I2 Jumper battery charging current configuration Ibat 0 5 A Ibat 1 0 A Legend jumper installed jumper removed B Battery terminal positive Fig 1 Description of terminals B Battery terminal negative Z1 Connector of optical signalization 2 4 Dimensions and fitting of the PSB1002435 power supply Fig 2 Dimensions of power supply 3 Maintenance Al...

Page 4: ...n as possible however not later that within 14 days from the delivering of the equipment to the service centre of the manufacturer 7 The repair period mentioned in item 6 may be prolonged if there is no technical capability to carry out the repairs and in the case that the equipment has been accepted conditionally due to the failing of the warranty terms by the claimant 8 All the services rendered...

Reviews: