background image

 

 

 

 

 

WEEE LABEL 

 

Waste electrical and electronic equipment must not be disposed of with normal household waste. 

According to the European Union WEEE Directive, waste electrical and electronic equipment 

should be disposed of separately from normal household waste. 

 

 

 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 

 
 

 
 

 
 
 

 
 

 

GENERAL WARRANTY CONDITIONS 

 

1. Pulsar (manufacturer) grants a two-year quality warranty for the equipment, starting from the production date. 
2. The warranty includes free-of-charge repair or replacement with an appropriate equivalent (selected by the manufacturer) if the 
malfunction is due to the manufacturer. It includes manufacturing or material defects, provided that such defects have been 
reported within the warranty period (point.1). 
3. The equipment subjected to warranty should be brought to the place of purchase or directly to the main office of the 
manufacturer. 
4. The warranty applies to complete equipment, accompanied by a properly filled warranty claim with a description of the defect.  
5.  Should the claim be accepted, the manufacturer is obliged to provide warranty repairs, at the earliest convenience, however not 
later that within 14 days from the delivery to the service centre of the manufacturer. 
6.  The repair period mentioned in point 5 may be prolonged, if there are no technical possibilities to carry out the repairs, or if the 
equipment has been conditionally accepted, due to the breaking warranty terms by the claimant. 
7.  All the services are carried out at the service centre of the manufacturer, exclusively. 
8. The warranty does not cover the defects of the equipment, resulting from:  
- reasons beyond the manufacturer's control,  
- mechanical damage,  
- improper storage and transport,  

use that violates the operation manual or equipment’s intended use  

- fortuitous events, including lightning discharges, power failures, fire, flood, high temperatures and chemical agents,   
- improper installation and configuration (failure to follow instruction). 
9. The warranty is void in case of construction changes and repairs carried out by any unauthorized service center or in case of 
damage or modifications to warranty stickers and serial numbers. 
10. The liability of the manufacturer towards the buyer is limited to the value of the equipment determined according to the 
wholesale prices suggested by the manufacturer on the day of purchase. 
11.  The manufacturer takes no responsibility for the defects that result from the damaging, malfunctioning or inability to operate 
the equipment especially when resulting from failure to comply with the recommendations and requirements contained in the 
manual. 

 

Pulsar  

Siedlec 150,  32-744 Łapczyca, Poland 

Tel. (+48) 14-610-19-40, Fax. (+48) 14-610-19-50 

e-mail

biuro@pulsar.pl

sales@pulsar.pl

 

http:// 

www.pulsar.pl

www.zasilacze.pl

 

Summary of Contents for S54







Reviews: