background image

By  pressing  the  mode  button,  the  user  choose  between  auto  mode  or  dryer  mode.

 

AUTO MODE

In  this  mode  the  relative  humidity  level  is  50%  and  the  fan  operates  at  high  speed 

mode.  Press  the  HUM  set  button  to  adjust  the  relative  humidity  level  to  your 

preference  between  30%  and  80%  by  5%  step  each  time  you  press  the  HUM  set

button. After 5 seconds of inaction the setting is saved.

DRYER MODE

When this function is selected, the fan operates in high speed mode. The user cannot 

change  the  fan  speed  between  LOW  and  HIGH.  During  this  function  the  compressor 

operate  continuously,  despite  the  relative  humidity  level  of  the  room. 

For  drying clothes  place  the  dehumidifier in  a  small  room  nearby  tha  clothes  racand 

close the door. The machine should be at a distance of 40-50cm from the clothes rack 

and not beneath them. For a quick result, clothes should be wringed out good.

Press  this  button  to  set  the  humidity  level.  The  user  can  set  the  level  between 

30%-80% by 5% step . While tha adjustment takes place, the count after 80% returns to 

30%.       30%-35%-40%-45%-50%-55%-60%-65%-70-%-75%-80%-30%-35%....

Press  the  ''Timer''  button  to  set  the  time  which  the  dehumidifier  will  start  or  end  its 

operation. The Timer indicator and the screen will light up. The user can set the time 

between  1-24  hours  with  step  every 

60

  minutes. 

When

  the  timer  set  value  is  "00",  it 

means that the Timer is disabled.

By pressing this button, the SLEEP function is activated. The dehumidifier operates in 

LOW  fan  speed,  and 

keeps

  the  relative  humidity

  levels

  between  57%

-

63%.

  It  is  not 

allowed to change the fan speed or the relative humidity level.

By pressing and holding the SLEEP button, the RESET function is activated. In this way 

the Filter change indicator is reset.

Summary of Contents for PD 2419 Sofia









































Reviews: