background image

FP / MP Series Water Filtration Housings

Guidelines & Warnings

The Puretec filter housing cartridges need replacing regularly to maintain optimum 
performance. Replace cartridges when water flow is reduced, taste or odour returns 
to water (carbon cartridges only) or every 6 to 12 months. For cartridge replacements 

contact your nearest Puretec stockist.

Customer Service Helpline

 

1300 140 140

 (Australia) 

0800 130 140

 (New Zealand).

Guidelines and Warnings

•   Where line pressure exceeds 520 kPa, a pressure limiting valve must be installed. 

Protect the housing from water hammer.

•   Use on cold water line only (with water up to 52°C). For installation over 52°C 

please enquire as to a suitable housing. Protect the housing from freezing.

•   Avoid installing in direct sunlight.

•  

Use PTFE thread seal tape on all connections. Use of liquid pipe sealants/

dope will void warranty.

•   Do not overtighten. Too much tape or over tightening may cause head to split.

•   For point of entry installations an approved dual check backflow prevention device 

must be fitted in accordance with national plumbing product codes.

•   Do not use with water that is microbiologically unsafe or with water of unknown 

quality without adequate disinfection.

•   This product must be installed in accordance with local plumbing regulations by a 

licensed plumber.

Installation Note

: A water filter system/tap, like any product, has a limited life 

and may eventually fail. Also sometimes failure happens early due to unforeseen 

circumstances.  To avoid possible property damage, this product should be regularly 

examined for leakage and/or deterioration and replaced when necessary. A drain pan, 
plumbed to an appropriate drain or outfitted with a leak detector, should be used in 

those applications where any leakage could cause property damage, and/or the water 

supply should be turned off if no one is home/present.  

INSTALLATION MUST BE COMPLETED BY A LICENCED PLUMBER. FAULTY 

OPERATION DUE TO UNQUALIFIED PERSONS WILL RESULT IN VOIDED 

WARRANTY COVERAGE. 

Summary of Contents for FP Series









Reviews: