background image

Warranty

Warranty

: Any claim under this warranty must be made within 3 years of the date of purchase 

of the product. This product is warrantied to be free of defect of material and workmanship for 

3 years from date of purchase. To make a claim under the warranty, take the product and proof 

of purchase to place where you purchased the product, and they will lodge a Warranty Request 

with Puretec. 3 year warranty is 1 year parts and labour plus 2 years parts only. Excludes 

consumables.

Puretec will pay your reasonable, direct expenses of claiming under this warranty. You may 
submit details and proof of your expense claim to place of purchase for consideration.

Warranty/Australia

This warranty is given by Puretec Pty Ltd, ABN 44 164 806 688, 37-43 Brodie Road, Lonsdale 
SA 5160, telephone no. 1300 140 140 and email at sales@puretec.com.au.

This warranty is provided in addition to other rights and remedies you have under law: Our 

goods come with guarantees which cannot be excluded under the Australian Consumer Law.  

You are entitled to replacement or refund for a major failure and to compensation for other 
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or 
replaced if the goods fail to be of acceptable quality and the failure does not amount to a 
major failure. 

Warranty/New Zealand

This warranty is given by Puretec Ltd, Reg. No 4464398, PO Box 875 Cambridge 3450, 
telephone no. 0800 130 140 and email at sales@puretec.co.nz.

This warranty is provided in addition to other rights and remedies you have under law: Our 

goods come with guarantees which cannot be excluded under the Australian Consumer Law.  

You are entitled to replacement or refund for a major failure and to compensation for other 
reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or 
replaced if the goods fail to be of acceptable quality and the failure does not amount to a 
major failure. 

The warranty only applies if the product was used and/or installed in accordance with the user 
guide and/or installation instructions. This warranty is given in lieu of all other express or implied 

warranties and manufacturer shall in no circumstance be held liable for damages consequential 

or otherwise or delays caused or faulty manufacturing except as excluded by law.

Applicable to all above, is that the Warranties need to be approved by Puretec to ensure product 

was not incorrectly used, installed or claimed. False and incorrect claims will be pursued at 

Puretec’s discretion, including chargeable inspection and labour costs incurred.

Warranty

Summary of Contents for ROS2700





















Reviews: