POWER VTX
®
WATER HEATER
8
PV500-68 06/16
3
WATER HEATER INSTALLATION
3.1 Checking Equipment Before You Install
•
Inspect the unit completely upon receipt from the freight carrier before signing the bill of lading. Inspect the
appliance and all accompanying parts for signs of impact or mishandling. Verify the total number of pieces shown
on packing slips with those actually received. Contact the freight carrier immediately if any damage or shortage is
detected.
•
Check the data decal on the appliance. Be sure the electrical, water and gas supply is adequate for the
installation.
•
Carefully remove all side and top shipping supports and bracing. If possible, do not remove the wooden base/skid
assembly until the product has been moved to its final location for installation and operation (see: Handling and
Locating the Water Heater).
3.2 Codes
The equipment must be installed in accordance with those installation regulations in force in the local area where the
installation is to be made. Authorities having jurisdiction must be consulted before installation is made. In the
absence of such requirements, the installation must be in accordance with the instructions in this manual, appliance
markings and supplemental instructions and in compliance with the latest edition of the National Fuel Gas Code,
ANSI Z223.1/NFPA 54. Where required by the Canadian authority having jurisdiction, the equipment must be
installed in accordance with the latest edition of the CAN/CSA B149.1-10 Natural Gas and Propane Installation Code
and applicable Provincial Regulations. All appliances conform to the current edition of the ASME Boiler and Pressure
Vessel Code, Section IV, Part HLW.
3.3 Electrical
Requirements
See appliance rating decal for electrical service requirements. The appliance must be electrically supplied and
grounded in accordance with the requirements of the authority having jurisdiction or, in the absence of such
requirements, with the latest edition of the National Electrical Code ANSI/NFPA No. 70. In Canada, the electrical
service must conform to local electrical codes and/or CSA C22.1, Canadian Electrical Code, Part 1.
•
All wiring between the unit and field installed devices must be made with type T copper wire.
•
Line voltage wire exterior to the appliance must be enclosed in approved conduit or approved metal clad cable.
•
To avoid serious damage,
DO NOT
energize the unit until the system and appliance is full of water.
Utiliser du fil de cuivre de la taille appropriée pour le service électrique entrant. Les dommages résultant de
l'utilisation de fil d'aluminium seront exclus du champ d'application de la garantie de cet appareil.
3.4 Handling and Locating the Water Heater
WARNING: Use industry standard safe rigging methods, such as strapping around the water heater
base/skid assembly and using spreader bars,
when attempting to lift or move this product. Failure to follow
industry standard safe rigging methods can result in property damage, serious injury or death.
1. The water heater must be located indoors.
2. This water heater can be installed directly on a combustible floor.
3. Locate the water heater in an area that is not exposed to freezing temperatures.
4. Locate on a level surface. Although not generally required, a housekeeping pad may be necessary when
additional elevation is required to properly drain condensate.
5. Locate the water heater near a floor drain. Locate the unit so if the tank or water connections should leak, water
damage will not occur to the adjacent area or to lower floors of the building. When such locations are
unavoidable, install an adequately drained metal drain pan underneath the water heater. The manufacturer’s
warranty does not cover water damage.
6. Floor mounting provisions and tie down anchor points are provided. Pilot holes are indicated on the jacket for
securing the equipment. Code requirements vary by geographical location, additional strapping or braces may be
required. Please refer to your local codes for specific requirements.
7. Protect associated electrical components and electrical connections from water (dripping, spraying, rain, etc.)
during appliance operation and service.
8. Locate the water heater where the vent and air intake piping, when installed, will remain within the maximum
equivalent lengths allowed. See Venting.
