PVI VuMATRIX 4K60-POE Manual Download | Manualshive

Page: 7 / 15

background image

4.    APP control use guide
4.1 Android User: Download the App from our pvisupport site by searching VUMATRIX APP
ANDROID
IOS User: Download the APP"Matrix Controller" from the APP Store.

.
4.2 Firstly, connect the video matrix controller to the IGMP switch.
Then, connect mobile phone/tablet and the video matrix controller via

hotspot

“

MATRIX

”

with each other (as figure 1 ). At this time, open the

downloaded APP

“

matrix control

”

, will enter to the interface as figure 2,

and APP control starts.

4.3 APP function
4.3.1 Preview
Click

”

play

”

button to preview the content of the source device.

«
...
5
6
7
8
9
...
»

Summary of Contents for VuMATRIX 4K60-POE
















Reviews:

No comments

Related manuals for VuMATRIX 4K60-POE

Brand: Dataprobe Pages: 31

Brand: IBM Pages: 13

Flex System EN2092

Brand: IBM Pages: 2

Brand: Lantronix Pages: 2

Brand: Vector Pages: 6

Brand: protech Pages: 4

Brand: Cabletron Systems Pages: 170

ToolBox GTB-MHDMI1.3-441

Brand: Gefen Pages: 25

Brand: PRO SIGNAL Pages: 4

Brand: Scion Pages: 8

Brand: GarrettCom Pages: 76

Brand: Allen-Bradley Pages: 2

Brand: Flamingo Pages: 2

Ethernet Switch Boards

Brand: Intel Pages: 52

LiteWave LS105G

Brand: TP-Link Pages: 3

Enova DGX 100 Series

Brand: AMX Pages: 2

Brand: Emulex Pages: 75

Brand: Exsys Pages: 14

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands