background image

100dB, unweighted    100dB, unweighted    100dB, unweighted    100dB, unweighted    100dB, unweighted    100dB, unweighted    100dB, unweighted    100dB, unweighted

10K Ohms per leg     10K Ohms per leg     10K Ohms per leg    10K Ohms per leg    10K Ohms per leg     10K Ohms per leg     10K Ohms per leg     10K Ohms per leg

300W RMS/chan     400W RMS/chan     500W RMS/chan     600W RMS/chan     700W RMS/chan     800W RMS/chan     900W RMS/chan     1000W RMS/chan

150W RMS/chan     200W RMS/chan     250W RMS/chan     300W RMS/chan     350W RMS/chan     400W RMS/chan     450W RMS/chan      550W RMS/chan

600W RMS             800W RMS             1000W RMS           1200W RMS          1400W RMS           1600W RMS           1800W RMS            2000W RMS

FEATURE SET: ALL Models (++indicates each channel)
COOLING SYSTEM: Two-speed DC fan, air flow back to front
LOW CUT +: -3dB @ 40 Hz, 12dB per octave
CRO+: 150Hz, 4-pole Linkwitz-Riley approximation
INPUT++: Electronic balanced; Barrier Strip, XLR, TRS 1/4" (6.3mm)
CROSSOVER O+: Low/Thru and High, TS 1/4" (6.3mm)
AMPLIFIER OUTPUTS: Speakons for Chan A, Chan B and Bridge; Binding, Posts
LED INDI+: Red, DDT/clipping; 

Green signal; Blue, power

AMP PROTECTION: Full short circuit, open circuit; over-temp thermal; RF; stable into any load
LOAD PROTECTION: Turn on/off muting, DC (triac crowbar), low-cut filter
MAINS VOLTAGES AVAILABLE 100, 120, 230, 240 VAC, 50-60 Hz
DIMENSIONS: Height: 3.5" (8.9cm), Width: 19" (48.3cm), Depth: 17.3" (44.1cm)

Specifications subject to change without notice

RATED OUTPUT POWER:

Stereo mode
(EIA both channels driven)
4 Ohms EIA, 1 kHz, 1% THD 
8 Ohms EIA, 1 kHz, 1% THD 
Bridge mode, mono
8 Ohms EIA, 1 kHz, 1% THD 

HUM & NOISE:

Stereo mode, below rated
output power, 4 ohms 

DISTORTION:

SMPTE-IM  

INPUT SENSITIVITY & IMPEDANCE:

@ rated output power, 4 ohms 
Balanced, TRS 1/4" phone jack 
Balanced, XLR (pin 2 positive)  
Overall system gain per channel 

 

DISTORTION: 

(THD, typical value)

Stereo mode, both channels driven, 4 Ohms
20 Hz to 20 kHz, 10dB below rated power
20 Hz to 2 kHz, at full rated power 

 

FREQUENCY RESPONSE:

Stereo mode, both channels driven
+0, -1 dB @1 W RMS, 4 ohms 
+0, -3 dB @rated output, 4 ohms 

DAMPING FACTOR:

 (Typical value)

Stereo mode, both channels driven
8 Ohms, 1 kHz  

40X(+32dB)            40X(+32dB)             40X(+32dB)            40X(+32dB)            40X(+32dB)            40X(+32dB)            40X(+32dB)           40X(+32dB)

less than 0.01%     less than 0.01%     less than 0.01%     less than 0.01%      less than 0.01%     less than 0.01%     less than 0.01%     less than 0.01%

0.87V RMS (-1.2d

BV

)     1V RMS (0d

BV

)       

 

  1.12V RMS (+1d

BV

)  

 

 1.23V RMS (+1.79d

BV

)  1.32V RMS (+2.4d

BV

)   1.4V RMS (+2.9

d

BV)  

 

  1.5V RMS (+3.5d

BV

)     1.58V RMS (+3.97d

BV

)

10K Ohms per leg    10K Ohms per leg     10K Ohms per leg   10K Ohms per leg    10K Ohms per leg    10K Ohms per leg    10K Ohms per leg    10K Ohms per leg

 less than 0.03%      less than 0.03%      less than 0.03%     less than 0.03%     less than 0.03%      less than 0.03%     less than 0.03%      less than 0.03%

 less than 0.03%      less than 0.03%      less than 0.03%     less than 0.03%     less than 0.03%      less than 0.03%     less than 0.03%      less than 0.03%

20Hz to 20 kHz         20Hz to 20 kHz         20Hz to 20 kHz        20Hz to 20 kHz        20Hz to 20 kHz         20Hz to 20 kHz         20Hz to 20 kHz         20Hz to 20 kHz

5Hz to 50 kHz            5Hz to 50 kHz            5Hz to 50 kHz            5Hz to 50 kHz            5Hz to 50 kHz            5Hz to 50 kHz            5Hz to 50 kHz             5Hz to 50 kHz

Greater than 300      Greater than 300       Greater than 300      Greater than 300      Greater than 300      Greater than 300       Greater than 300       Greater than 300

SPECIFICATIONS

Summary of Contents for PTA3000














Reviews: