Pyle Sports PSKIW25 User Manual Download

Page: 14 / 15

13.8 Calibrating Mode - Calibration the Compass

13.9 Calibrating the Compass - Compass Rotation Calibration Mode

13.10 Calibrating the compass -

Magnetic Declination Mode

When to Calibrating the Compass

The Watch has to employ a compass calibration

in one of the following conditions:

1) The Watch is using for the first time,

How to Calibrate the Compass

The  compass  calibration  includes  two  different
p r o c e s s e s :  R o t a t i o n  C a l i b r a t i o n  M o d e  a n d
Magnetic  Declination  Setting.

It is advisable to carry out them both from time
to time, that achieves a more accurate reading.

IMPORTANT

: If the Watch has not been calibrated,

the direction made by the Watch may be a
inaccurate direction.

2) The battery has been replaced,

3) The bearing direction digits are flashing, and

the "

OFF CAL

" indicator appear,

4) The compass use in a location that is apart

from the place in which the compass had
been calibrated,

5) The user intends to regulate the precision of

the digital compass.

Rotation Calibration Display

To select the Rotation Calibration Display, hold
the [M] button in Compass Mode.

To  start  rotation  calibration,  press  [S/S]  button
once.  The  pointers  will  start  rotating,  turning  the
watch  (keep  parallel  to  the  horizon)  in  the  same
direction  of  the  rotating  pointers  for  more  than  2
turns.

Press [S/S] or [L/R] button to stop the calibration
when the 2-turn rotation calibration is completed.

When  the  pointer  stop  rotating,  hold  the  [M]
button  to  go  back  to  the  Compass  Mode  or  press
t h e  [ M ]  b u t t o n  o n c e  t o  s e t  t h e  m a g n e t i c
declination.

Magnetic Declination Mode

C h e c k   t h e   p r e v i o u s   s e c t i o n   " M a g n e t i c
Declination  at  Major  Cities"  to  get  the  magnetic
declination  of  the  city  which  is  close  to  your
current  position.  That  value  will be  input  into  the
Watch  during  the calibration.

To select Magnetic Declination Display, press the
[M] button in Rotation Calibration Display.

When  the  current  magnetic  declination   appears,
press  the [S/S]  or  [L/R]  button  to  increase  /
decrease  the  number.  (Hold down  the  button  to
change  the  number  at  a  higher speed).

If the setting is completed, hold the [M] button to
confirm the setting and exit the adjustment
display.

Magnetic
Declination Display

Compass Calibration

Rotation
Calibration Display

Rotation Calibration
Stop Display

Rotation Calibration
Turning Display

Hold [M]

[M]

Compass Mode

Compass Mode

14.0 Battery -

Battery Low Indication and Battery Replacement

Battery Low Detection

When  the  battery-low  indicator  appears  on  the
display,  it  means  that  the  capacity  of  the
battery  is  low.  It  is  recommended  to  replace  the
battery  with  a  new  CR2032  battery.

However,  if  the  appearance  of  the  battery-low
indicator  is  caused  by  using  the  Watch  under
very  cold  condition,  the  indicator  will  disappear
when  normal  temperature  returns.

NOTE:

It is recommended to complete the battery

replacement by

Watch

If the battery is replaced, all memory

w i l l  b e  c l e a r e d .  F o l l o w  t h e  p r e v i o u s  c h a p t e r
"Calibrating  the  Compass"  to  calibrate  the  compass
before  using  the  Compass.

a certified service agency because

this

contains delicate electronic sensors and

components.

IMPORTANT

Batte ry -
In dic ato r

Low

SE T

[S/S] / [L/R]

[S/S]

pointers
rotated at
15 seconds
per round

[S/S]/[L/R]