background image

5

INSTALLATION

• Use the supplied parts and mount the unit securely. The use of parts other than 

these supplied (specified) may loosen or damage internal components.

• If installation presents any difficulties, consult your dealer for advice.
• Before drilling a hole into the wall or floor the vehicle trunk, check that nothing is

behind the panel. Never drill a hole in the fuel tank or any other important that may
be attached to the trunk.

• Take off the negative terminal connector (–) of the car battery to prevent short

circuits while you are installing the unit.

Location

• Be sure to mount the unit in a location that will not interfere with the driver or 

passengers. Be certain there is not danger of passengers being injured case of 
sudden stops.

• Do not mount the player near heater outlets, where it might be affected by heat; or

near doors, where rainwater might splash onto it.

• Do not mount the player in a location that will receive direct sunlight, such as on 

the dashboard or the rear shell. Excess heat will damage the player.

• When mounting the player make sure no wires are trapped between the player and

the surrounding metalwork or fittings.

• Do not mount the player on the spare lire board or any other unstable place.
• Do not mount the player where it will impede access to the spare tire, jack or tools.
• Although the player can be mounted horizontally, vertically or at 45

°

, keep to the

tolerable angles shown on following page. In addition, choose a place where the 
CD magazine can be loaded and unloaded easily.

TOP

FRONT

Proper

Improper

TOP

FRONT

Summary of Contents for DISC CD CHANGE













Reviews: