manualshive.com logo in svg

Pyle PLXR2B, User Manual

The Pyle PLXR2B is a high-quality audio receiver, perfect for enhancing your car's sound system. For easy installation and optimal performance, make sure to consult the comprehensive User Manual available for download free of charge at 88.208.23.73:8080. With step-by-step instructions and clear illustrations, you'll have your new receiver up and running in no time.

Share
Download
background image

Control Panel Layout

www.PyleUSA.com

3

FUNCTIONS

FUNCTIONS

1. POWER INPUT CABLE (12V)

     To be connected to the positive terminal of your vehicle battery or other
     co12V source.

2. GROUND INPUT CABLE (GND)

     To be wired to the vehicle's chassis ground.

3. REMOTE TURN-ON INPUT CABLE

     To be connected to the remote control wire or antenna lead of the source unit
     for remote ON/OFF. If it is not available, connect the orange lead to a switched
     +12 volt source (e.g. The ignition switch)

Summary of Contents for PLXR2B















Reviews:

No comments

Related manuals for PLXR2B

Coustic XM6 Owner'S Manual preview
XM6
Brand: Coustic Pages: 15
Crown SST-MX Specification Sheet preview
SST-MX
Brand: Crown Pages: 1
Stageline MCX-2100 Instruction Manual preview
MCX-2100
Brand: Stageline Pages: 18
EAW UX8800 Owner'S Manual preview
UX8800
Brand: EAW Pages: 40

Brands by name

Popular brands

Load more brands