background image

27. RPT  

 Under DVD mode, allows the user to repeat playback:  
 repeat mode:  disc, track/chapter 

 

28. Angle + / - 

It

 

is not available. 

 

USING REMOTE CONTROL

 

 
Aim the IR remote control directly at the unit, or video source with an IR input. 

Tips:

  

− 

Maximum IR distance is 3 meters from the sensor. 

− 

Direct sunlight or very bright light reduces sensitivity to the IR remote signal commands. 
Make sure the monitor is not located in direct sunlight. 

− 

Obstruction between the remote sensor and remote control may disrupt reception.   

 
BATTERY 

 

 
If the remote control does not function the operating range is shortened, please change to a 
new battery. 
 
1. Pull out the battery holder. 
    Follow the arrow 1 slide it to the right toward the battery 

while at the same time pull the battery holder away from the 
remote control.  

 
2. Insert a new battery with the (+) side up. (The type of battery: 
    Crd2025).

 

 
3. Push to close the holder. 
   You will hear a small clicks as the tray locks. 
 

Batteries contain chemical substances, so they should be disposed of properly.

 

 
Tips: 

 

Remove batteries if they are empty or if the remote control will not be 

used for a long time.  

 

Battery and small parts can be a choking hazard. Keep the remote control away from 
young children.

 

 

 

 
 
 
 
 
 

6

Summary of Contents for View PL2DNTV7

















Reviews: