background image

8

9

INSTaLLaTIoN aND oPeraTIoN MaNUaL SoLar MoDULeS GeNeraTIoN 3 (G3) – HaNWHa Q CeLLS aUSTraLIa PTY LTD

INSTaLLaTIoN aND oPeraTIoN MaNUaL SoLar MoDULeS GeNeraTIoN 3 (G3) – HaNWHa Q CeLLS aUSTraLIa PTY LTD

Fig. 2: 

installation options for crystalline Q ceLLs modules. All dimensions are given in mm. Also observe the  

 

 

allowed static loads and clamping range as specified on the following page.

 

 

the illustrated installation options apply for both horizontal and vertical module orientation. 

 

Module 

Clamp 

Subconstruction 

Mounting profile

2.3  Mounting options

2 PLaNNING

TYPe of 
INSTaLLaTIoN

MoDULe

PoINT MoUNTING SYSTeM

LINear MoUNTING SYSTeM

INSTaLLaTIoN WITH  
CLaMPS

Q.PRo-G3 
Q.PRo BLK-G3
Q.PeAK-G3
Q.PLus-G3

INSTaLLaTIoN  
oN  
MoUNTING  
PoINTS

Q.PRo-G3
Q.PRo BLK-G3
Q.PeAK-G3
Q.PLus-G3

INSTaLLaTIoN WITH  
INSerTIoN ProfILeS

Q.PRo-G3
Q.PRo BLK-G3
Q.PeAK-G3
Q.PLus-G3

not permitted

IP1

IP2

CL3

CL4

245 - 445

180 - 380

0 - 300

0 - 300

CL1

245 - 445

180 - 380

2 PLaNNING

2.3  Mounting options

Specifications

 

MoDULe TYPe

MoUNTING oPTIoN

CLaMPING raNGe

1

 

[MM]

aLLoWeD STaTIC 
LoaD

[Pa]

TeST LoaD 
aCC. IeC 61215 [Pa]

Q.PRO-G3

Q.PRO BLK-G3 

Q.PEAK-G3

Q.PLUS-G3

CL1

Push

245 - 345
346 - 445

3500
2400

5400

Pull

245 - 345
346 - 445

5650
4000

CL3

Push

245 - 445

5700

Pull

245 - 345
346 - 445

4000
4000

CL4

Push

0 - 300

2000

Pull

0 - 300

2000

FB1

Push

3500

Pull

3100

FB2

Push

4000

Pull

3100

IP1

Push

-

3700

Pull

-

3700

IP2

Push

-

1800

2400

Pull

-

1800

1

 Distance between outer edge of module and middle of the clamp.

2

 Describes the maximum module surface load (vertical to the module surface) regarding safety factors (e.g. euRocoDe). 

For this purpose, the load value determined by load tests according to various criteria: laminate overlay, plastic 
deformation, module failure, and were divided with a safety factor. the minimum calculated load value corresponds 
to the maximum permitted load. 

345

280

FB2

4 x Fastening 
points

4 x Fastening 
points

345

4 x Fastening 
points

280

4 x Fastening 
points

FB1

CL1

245 - 445

180 - 380

CL3

CL4

245 - 445

180 - 380

0 - 300

0 - 300

345

4 x Fastening 
points

280

4 x Fastening 
points

FB1

345

280

FB2

4 x Fastening 
points

4 x Fastening 
points

IP1

IP2

Summary of Contents for Q.Pro-G3













Reviews: