INSTALLATION
LED POWER SUPPLY - QOM-eLED+DMX
© 2020 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | sales@q-tran.com | www.q-tran.com
Specification subject to change. Rev-09-29-20
Connecting and Configuring the LINEARdrive 100D/180D
Primary Wiring
Secondary Wiring
Control Wiring
DMX Connections
Commonly Asked Questions
1) How can I verify my installation?
•
Apply AC input, verify display turns on : This confirms AC input wiring
•
Run “Visual Test Run” : This verifies wiring of LEDs. Make sure LEDs turning on go in same order as the Test Run
2) I don’t have a controller yet, how can I keep my lights on?
•
Change the Mode to “COLOR” : This allows to manually set a specific color to be on
•
Adjust the Hue or WHITE to achieve the desired color : This sets that specific color
3) My LEDs aren’t coming out the right color. They look like white has been added in
•
Verify the Network Resolution “NETW RES” : Default is 8 BT
•
Check your DMX Programming. Stick controllers come with RGB programs by default. This will cause RGBW
LEDs to show Pink vs. Red
To DMX Controller
Ext in +
Ext in
DMX in +
DMX in -
DMX in shield
LedSync thru +
LedSync thru -
LedSync shield
LINEARdrive 180D
-
12-28V
/ 6
A Direct voltage controlled LED driver
Ext in +
Ext in
DMX in +
DMX in -
DMX in shield
LedSync thru +
LedSync thru -
LedSync shield
LINEARdrive 180D
-
12-28V
/ 6
A Direct voltage controlled LED driver
DMX in shield LedSync shield
DMX in -
LedSync thyu -
DMX in + LedSync thyu +
Blue Wire = Blue LED
Red Wire = Red LED
Green Wire = Green LED
White Wire = White LED
Black Wire = +24V
A
C
LED DRIVER 2
(120 - 277V)
B
M
-
+
GND
NEU
SECONDARY
PRIMARY
DMX Shield
DMX -
DMX +
-
+
iQ-LED
Blue = Blue
White = White
Green = Green
Red = Red
Black = +24V
W B G R +24
W B G R +24
DMX OUT
iQ-LED
M
-
+
DMX in +
DMX in -
DMX Shield
LedSync thru +
LedSync thru -
LedSync Shield
DMX IN DMX OUT
HOT
NEU
GND
HOT
GND
HOT
NEU
LED DRIVER
(120 - 277V)
NEU
GND
HOT
DMX IN
GND
HOT
NEU
LED DRIVER (120 - 277V)
NEU
GND
HOT
M
-
+
iQ-LED
TC
1
2
3
Group
Group
Group
Group
LED
LINEARdrive 180D
4
Black Wire = +24V
Red Wire = Red LED
Green Wire = Green LED
Blue Wire = Blue LED
White Wire = White LED
iQ-LED
W
B
G
R
+24
Ext in + Ext in
DMX in +
DMX in -
DMX in shield
LedSync thru +
LedSync thru -
LedSync shield
-
DMX in shield
DMX in -
DMX in +
DMX
WARNING:
Risk of electrical shock. May result in serious injury or death. Disconnect power before servicing or installing.
CAUTION:
The device may only be connected and installed by a qualified electrician. All applicable regulations, legislation and building codes must be observed.
Incorrect installation of the device can cause irreparable damage to the device and the connected LEDs.
●
DMX Shield must be grounded to Earth Ground at a single point external to power supply
