QTM-eLED+DALI-DT6
LED POWER SUPPLY 100W–300W
© 2022 Q-Tran Inc. All rights reserved | 155 Hill St. Milford, CT 06460 | 203-367-8777 | sales@q-tran.com | www.q-tran.com
Specification subject to change. Rev-11-15-22
COMPLIANT
12V - 36V DC IN
•
To connect the driver to a DC power supply unit (PSU), connect the PSU’s positive voltage supply wire to the VDC+ connector and the
PSU’s negative voltage supply wire to the VDC- connector.
DALI Signal in/out
•
Use these connectors when the driver is used in a DALI network. For DALI in, connect the network cable’s DALI+, to the D1+, and D1-
connectors respectively. For DALI out, connect the network cable’s DALI - to the D2+, and D2- connectors respectively.
•
Separate DALI Bus power supply required. By others.
LED groups
•
Indicates the location of the connectors for your LED groups. 1(-) represents channel 1, 2(-) represents channel 2, 3(-) represents
channel 3 and 4(-) represents channel 4. The default group color allocation can be changed over the 2-button user interface.
Wiring Diagram
To DALI Controller
V-
V-
V+
V+
+
1(-)
2(-)
3(-)
4(-)
12-36VDC IN
LED groups
D1+
D2+
D1-
D2-
DALI Signal
in/out
D1+
D2+
D1-
D2-
{
12-36VDC IN
-
+
2
1
0.2-1.5 mm
2
0.35 inch
0.5-1.5 mm
2
AWG 20-16
0.35 inch
AWG 24-16
VDC and LED connectors:
Other connectors:
LED
V- V- V+ V+ + 1(-) 2(-) 3(-) 4(-)
12-36VDC IN
LED groups
D1+
D2+
D1-
D2-
DALI Signal
in/out
V- V- V+ V+ + 1(-) 2(-) 3(-) 4(-)
12-36VDC IN
LED groups
D1+
D2+
D1-
D2-
DALI Signal
in/out
V- V- V+ V+ + 1(-) 2(-) 3(-) 4(-)
12-36VDC IN
LED groups
D1+
D2+
D1-
D2-
DALI Signal
in/out
DALI
Controller
*By Others
DALI Bus
Power Supply
*By Others
V- V- V+ V+ + 1(-) 2(-) 3(-) 4(-)
12-36VDC IN LED groups
D1+
D2+
D1-
D2-
DALI Signal
in/out
DALI
OUT
DALI
IN
DALI
Controller
*By Others
DALI Bus
Power Supply
*By Others
-
+24V
-
+
V- V- V+ V+ + 1(-) 2(-) 3(-) 4(-)
D1+
D2+
D1-
D2-
12-36VDC IN LED groups
DALI Signal
in/out
DALI
OUT
DALI
IN
DALI
Controller
*By Others
DALI Bus
Power Supply
*By Others
Warm
Cool
+24V
+24V W C
3-Wire
2-Wire
2A - 2 Addresses
1A - 1 Addresses
NOTE:
2-Wire default is 1 address
3-Wire default is 2 addresses
For customization or pre-programming
contact a local sales rep.
DALI commissioning to be performed by
a third party at time of installation.
