background image

 

QT

300

Revision:

 

1

 

 

QT

300

 

User

 

Manual

 

Page

 

5

 

of

 

11

 

Q5X

 

Systems,

 

Inc.

 

2018

 

 

Ce dispositif fonctionne selon un régime de non-brouillage et de non-protection. Si l’utilisateur 
devait chercher à obtenir une certaine protection contre d’autres services radio fonctionnant 
dans les mêmes bandes de télévision, une licence radio serait requise. Pour en savoir plus, 
veuillez consulter la Circulaire des procédures concernant les clients CPC-2-1-28, 

Délivrance 

de licences sur une base volontaire pour les appareils radio de faible puissance exempts de 
licence et exploités dans les bandes de télévision

d’Innovation, Sciences et Développement 

économique Canada.

 

RF

 

Exposure

 

Compliance:

 

 

The QT-300 Module is granted with a modular approval for mixed mobile and portable applications.

 The 

module is to be used by Quantum5X in their final products without additional FCC/ISED

  

(Innovation, Science and Economic Development Canada) 

certification if they meet the following 

conditions. Otherwise, additional FCC/ISED approvals must be obtained. 
 
 

Mobile

 

Application

:

 

 

 

1) 

This

 

equipment

 

complies

 

with

 

radiation

 

exposure

 

limits

 

set

 

forth

 

for

 

an

 

uncontrolled

 

environment.

   

This

 

equipment

 

should

 

be

 

installed

 

and

 

operated

 

with

 

minimum

 

distance

 

20cm

 

between

 

the

 

radiator

 

and

 

your

 

body.

 

 

2)  This transmitter must not be co-located or operating in conjunction with any other antenna or 

transmitter. 

3)  To comply with FCC and ISED regulations limiting both maximum RF output power and human 

exposure to RF radiation, the maximum antenna gain including cable loss in a mobile-only 
exposure condition must not exceed the 3 dBi.   
 
 

4)  For Canada, the EIRP power shall not to be greater than 250mW to meet ISED regulations 

(Conducted power plus antenna gain)  

 

 

 

Portable

 

Application

:

 

 

This

 

low

 

power

 

module

 

when

 

used

 

in

 

the

 

specfied

 

host

 

configgurationzs

 

listed

 

below

  

complies

 

with

 

applicable

 

RF

 

exposure

 

requirements

 

that

 

meet

 

FCC/ISED

 

for

 

a

 

portable

  

device,

 

which

 

are

 

approved

 

with

 

this

 

filing.

  

For

 

this

 

application

 

see

 

the

 

the

 

output

 

power

 

reduction

 

settings

 

in

 

specifiation

 

table

 

page

 

8.

   

PlayerMic

 

AquaMic

 

Incognito

 

BeltMic

 

 

Summary of Contents for QT-300












Reviews: