background image

 

 

6 marzo 2018 

 

 

2.2

 

Environmental conditions  

 

WARNING

 

 

Do not keep or operate the end-effector in a place with 
high temperature or humidity. 

 

 

This  product  is  not  waterproof.  Never  operate  the 
product in a wet place. 

 

 

For indoor use only. 

 

 
 

2.3

 

EC Directives on product safety 

 

The following EC directives on product safety must be observed. 

 

 

If  the  product  is  being  used  outside  the  UE,  international,  national  and 
regional directives must be also observed. 

 
Machinery Directive (2006/42/EC) 
Because of their small size, no serious threats to life or physical condition can normally 
be expected from electric miniature drivers. Therefore, the Machinery Directive does 

not  apply  to  our  products.  The  products  described  here  are  not  “incomplete 
machines”

, so installation instructions are not normally issued by qbrobotics. 

 
Low Voltage Directive (2014/35/EU) 
The Low Voltage Directive applies for all electrical equipment with a nominal voltage 
of 75 to 1500 V DC and 50 to 1000 V AC. The products described in this device manual 
do not fall within the scope of this directive, since they are intended for lower voltages. 
 

 

Summary of Contents for qb SoftHand RESEARCH

















Reviews: