background image

INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK DUO ML-G11.X

INSTALLATION AND OPERATION MANUAL SOLAR MODULES Q.PEAK DUO ML-G11.X

16

17

4 Electrical connection

4.2 Electrical installation safety

Danger! Risk of fatal injury due to electric shock!

  Be sure to maintain the time intervals as specified by 

the inverter manufacturer between switching off the 

inverter and beginning any further work.

Danger! Risk of fatal injury due to electric shock!

  Never plug or unplug the cable when under load. 

Modules must not carry any current.

1. Switch off the inverter.

OFF

EN

2. Switch off the DC circuit breaker.
3.  Measure shutdown in DC String. 

(no DC current flow).

4.  Disconnect plugs by the use of appropriate 

and qualified tools of the manufacturer.

5.  When connecting the modules proceed in reverse 

order.

Danger! Risk of fatal injury due to electric shock!

  Electrical work may only be performed by qualified 

and skilled personnel (see page 3).

  Ensure correct polarity.

4 Electrical connection

4.3 Connection of modules

  Use solar cables for the connection at the junction 

box outlet.

  Only interconnect connectors of the same type and 

manufacturer.

  Use minimum 4 mm

2

 copper wires insulated for a 

minimum of 90 °C for field connections.

Note! Module damage may occur!

  Ensure that the cabling is not under mechanical stress 

(Comply with bending radius of ≥ 60 mm).

  Ensure that the cables do not run between module 

and mounting rail or structure (danger of pinch).

  Ensure for a tight connection between the plugs. 

Plugs click together audibly.

EN

click

Danger! Risk of fatal injury due to electric shock!

  Ensure that all electrical components are in a proper, 

dry, and safe condition.

  To avoid complex cabling arrangements, it is often 

advantageous to rotate some modules 180°.

  Module orientation can clearly be identified from the 

front side by the serial number and barcode labelled 

behind the module glass on the side with negative 

connection cable.

SOLAR

EN

Inverter

180°

180°

  Do not connect modules with different orientations or 

angles of inclination in the same string.

Summary of Contents for Q.PEAK DUO ML-G11 Series













Reviews: