CARTRIDGE PREPARATION AND USE
DRY
• Remove mouthpiece from cartridge body
• Place shredded dry herb loosely in chamber, below white
chamber wall
• Replace mouthpiece and slide cartridge into vaporizer chassis
• If desired, set your preferred temperature (see instructions)
• Press and hold button for 3 seconds to begin precision heating
• As the QuickDraw 500 warms to temperature, Indicator Ring
will glow red, then yellow, then green when ready for use
• Draw from mouthpiece, without pressing or holding button
• Press and hold button for 3 seconds to deactivate
• The
QuickDraw 500 will auto-deactivate after 2 minutes to
prevent undesired use
LIQUID
• Twist to remove mouthpiece from the cartridge
• Unscrew metal cap on the liquid tank
• Fill chamber with liquid, below overflow line
• While filling, hold cartridge at an angle to prevent liquid from
entering central vapor path
• Reattach mouthpiece and slide cartridge into vaporizer chassis
• Press and hold button as you draw
• If held for longer than 10 seconds, the QuickDraw 500’s
Indicator Ring will flash before device shuts down, preventing
undesired use
INTENSITY GAUGE
SETTING THE QUICKDRAW’S 500 VOLTAGE
The QuickDraw 500 has 3 different voltage settings for Liquid
and Extract cartridges: 3.7 V, 4.2 V, and 4.7 V. Choosing a higher
voltage setting on the QuickDraw 500 will produce more vapor.
• To set the voltage on the QuickDraw 500, rapidly press the
heating button twice.
• Now in Voltage Setting mode, the LED lights below the heating
button will cycle, indicating different voltage settings:
- 3.7 V when the bottom LED glows;
- 4.2 V when the bottom and middle LEDs glow;
- 4.7 V when all three LEDs glow.
• To make your selection, press the heating button when the
glowing LED(s) correspond with your desired voltage.
SETTING DRY CARTRIDGE TEMPERATURE
The QuickDraw 500 also has 3 temperature settings for its Dry
Herb cartridge: 200C/390F (low), 210C/415F (medium), and
225C/440F (high).
• To select a temperature setting on the QuickDraw 500, rapidly
press the heating button twice.
• Now in Temp Setting mode, the white LEDs below the heating
button will begin to cycle.
- Low temperature is activated when the bottom LED glows;
- Medium temperature when the bottom and middle LEDs glow;
- High temperature when all 3 LEDs glow.
• To make your selection, press the heating button when the
glowing LED(s) correspond with your desired temperature.
PLEASE CONTACT QUICKDRAW’S
EXPERT SUPPORT TEAM WITH ANY
QUESTIONS OR CONCERNS.
1 (800) 591-3613
Visit HoldYourFire.com for
product news and updates or to
view QuickDraw’s entire line of
vaporizers and accessories.
©2015 QD Products, LLC.
QuickDraw, and the QuickDraw
logo, are trademarks of QD
Products, LLC.
All rights reserved.
PREPPING THE QUICKDRAW 500
FAST CHARGING
To fully charge the QuickDraw 500 before use, attach the magnetic
charger tip to the end of the device and insert the cord into a USB
port. Both the LED and Indicator Ring will flash white to signal
charging. The Indicator Ring will turn red intermittently while
charging, and will turn green when the device is fully charged.
• LED Ring and Indicator Ring will begin a set of double blinks
that dim off gradually when a recharge is needed.
• The QuickDraw 500 is specifically designed to allow use
while charging.
UNLOCKING THE QUICKDRAW 500
The QuickDraw 500 is equipped with a 3-click battery lock to
prevent unintentional activation. Pressing the heating button 3
times rapidly will unlock the device for use, which the LED Ring
and Indicator Ring will signify by flashing.
To lock the QuickDraw 500, press the heating button rapidly in
the same fashion. The Indicator Ring will flash red to signal the
device is locked.
EXTRACT
• Unscrew mouthpiece from cartridge body
• Place extract in chamber, below overflow line
• Reattach mouthpiece and slide cartridge into vaporizer chassis
• Press and hold button for 3 seconds to begin heating. The light
on the Indicator Ring will glow red at the beginning of the cycle.
• The
QuickDraw 500 will auto-deactivate after 30 seconds to
prevent undesired use
Unpack and
fully charge device.
Replace mouthpiece
and slide cartridge into
vaporizer chassis.
1
2
4
3
THE 3-CLICK LOCK
Please note: if your vaporizer doesn’t light up when you press the
button, it’s most likely locked. Press the heating button three
times rapidly to unlock it for use.
CARTRIDGE MAINTENANCE
The QuickDraw 500 comes equipped with a kit of cleaning and
maintenance tools that should be used regularly to clear the device
and its cartridges of debris. Regular cleaning will ensure long
cartridge life.
Unscrew cartridge
mouthpiece and fill
chamber.
Press heating button 3
times to rapidly unlock
device for use.
HIGH
MEDIUM
LOW
