56
To use an automatic
proxy server
configuration, select the
Automatic proxy configuration
in the
Proxy server
drop down list then enter the PAC file
URL allowing to get automaticall the proxy server configuration.
For example:
https://domain.contoso.en/dir/my-proxy-auto-conf.pac
◬
The
LAN_1
configuration is dynamically taking into account the new
LAN_1
parameter as soon as the user changes from IP address
allocated by DHCP to static IP address or changes the static IP address value then click on the
Validate
button of the device configuration Web
user interface.
◬
The devices uses only one network interface at a time. The
WLAN_1
has priority over
LAN_1
.
◬
In DHCP mode, if neither the
LAN_1
connectivity nor the
WLAN_1
connectivity is working or the
WLAN_1
interface is deactivated, the IP
address value is
unavailable
. In some case, a valid IP address can be got back few dozens of seconds after the network connectivity is restored
on
WLAN_1
interface or on
LAN_1
interface.
Procedure to configure the
LAN_1
interface with the configuration Web user interface when your network supports DHCP:
.
it is considered here that the network connectivity is OK over the
LAN_1
interface,
.
connect to the device configuration Web user interface with a Web browser with the DHCP IP address of the
LAN_1
interface. You can
still connect to the device configuration Web user interface with its
LAN_1
IPV6 address (for example
http://[fe80::21c:e6ff:fe02:5694]
get from the
MAC
value written at the back of the NAPOE109XX device).
Procedure to configure the
LAN_1
interface with the configuration Web user interface when your network does not support DHCP:
.
it is considered here that the TAB10s device is connected to a
NAPOE109ku
device or to a
NAPOE109kt
, or to a
NAPOE109ft
device which
is connected to a PoE switch,
.
disconnect the RJ45 cable (
cable1
for
network1
) from your computer,
.
connect a RJ45 cable (
cable2
for
network2
) between your computer and the PoE switch,
.
connect to the device configuration Web user interface with a Web browser with its
LAN_1
IPV6 address (for example
http://[fe80::21c:e6ff:fe02:5694]
get from the
MAC
value written at the back of the NAPOE109XX device),
.
deactivate
IP address get by DHCP
for
LAN_1
and enter a suitable static address configuration (IP address, subnet mask, gateway,
DNS),
.
reboot the device with the device configuration Web user interface,
.
disconnect the RJ45 cable (
cable2
for
network2
) from your computer and reconnect the previous RJ45 cable (
cable1
for
network1
),
.
connect to the device configuration Web user interface with a Web browser with the valid
LAN_1
IP address of the device. You can still
connect to the device configuration Web user interface with its
LAN_1
IPV6 address (for example
http://[fe80::21c:e6ff:fe02:5694]
get from the
MAC
value written at the back of the NAPOE109XX device).
Summary of Contents for TAB10s
