QEP MTCT600 Operating Manual Download

Page: 2 / 16

PRODUCT DESCRIPTION

The machine is designed for cutting; plasterboard, aluminium, wood, tile and plastics.
Our machine is not suitable for processing any substrates containing asbestos.

You must abide by certain safety precautions when using the Multi Saw. In order

to prevent injuries and damages from occurring, you must always read through

this operating manual carefully.

This manual must be kept in a safe place so that the information that it contains is always

available. This operating manual must accompany the equipment if it is transferred to

somebody else.
We do not accept any liability for accidents or damage arising from ignoring this manual

and the safety instructions.

SPECIFICATIONS

Model No.

MTCT600

Power

600W

Voltage

230-240V 50Hz

Speed

7400 RPM

Blade diameter

85mm

Protection class

Double insulated

Tel: 01335 347300

Multi Saw Instructions

Safety and Operating Manual

Code

Description

Barcode

BHSS85

85mm HSS Blade

5011204616749

BDIA85

85mm Diamond Blade

5011204616756

BTCT85

85mm TCT Blade

5011204616763

REPLACEMENT BLADES

Summary of Contents for MTCT600

















Search results

Summary of Contents for MTCT600

Reviews:

Related manuals for MTCT600

Brands by name

Popular brands

QEP MTCT600, Operating Manual

Search results

Summary of Contents for MTCT600

Reviews:

Related manuals for MTCT600

Brands by name

Popular brands