background image

 
 
 

 

OPERATION 

 
FUEL & OIL 

 

WARNING 

YOUR MACHINE IS SUPPLIED WITHOUT ENGINE OIL OR PETROL 

Operating the engine with insufficient oil, can have catastrophic consequences. Any failure 

caused by 

insufficient oil, will not be covered by the manufacturer’s warranty.

 

READ INSTRUCTIONS CAREFULLY. 

 

Fuel & its vapors are very flammable. Do not use or fuel the machine near a flame, sparks or 

while smoking. 

Allow the engine to cool for more than 3 minutes, before re-fueling. Never fuel the machine 

with engine running. Fuel the engine at least 15 metres away from your work area. Always 

fuel your machine outdoors. 

IMPORTANT:  

Fuel which is older than 30 days old can become stale and cause acid & gum deposits in the 
fuel system or essential carburettor components. This could result in starting issues which 

would not be covered by your manufacturer’s warranty. 

 

Ensure that any stored petrol is clearly marked in a separate appropriate canister for a 
maximum of 30 days, if not mixed with a fuel additive. If the machine is not going to be used 
for a long period, drain the fuel tank, start the engine and drain the carburetor of any 
remaining fuel. 

 

To keep fuel fresh, we recommend you use SURE-START FUEL ADDITIVE (HP-199) from Handy 
Parts. A fuel additive added to your fuel at the time of purchase, will help make your 
machine easier to start, extend the shelf life of your fuel mixture for up to two years, keeps the 
carburettor & engine clean, plus reduces emissions and increases fuel economy. A 250ml 
bottle of SURE-START FUEL ADDITIVE will treat 25 litres of fuel. Only use 4-stroke SAE30 or 10W/30 
air cooled lawnmower engine oil. DO NOT USE automotive or marine oil. 
 

FUELING THE MACHINE 

Place the machine onto a solid flat surface, ensuring the engine is not running. Let the 
engine rest for a minimum of two minutes. Fill the fuel tank outdoors or in well-ventilated 
areas. 
Unscrew the fuel cap slowly and fill the fuel tank with clean, less than 30 days old unleaded 
petrol with an Octane rating of 90 or higher. Fill to a maximum of 80% capacity. This will allow 
the fuel tank to expand. Fasten the fuel cap tightly, being careful not to cross-thread. This will 
also prevent loosening through vibration during use. Wipe away any spillage, with an 
appropriate material.  If the machine has continued leaks, the product should not be started. 
Never use the machine with damaged ignition cable or spark plug cap, as there is a risk of 
sparks 

 

WARNING 

Fuel and its vapors are extremely flammable and explosive. Fire or explosion can cause 

severe burns or death. 

 
 
 
 
 
 

Summary of Contents for QG40-145SP





































Reviews: