background image

FIRST YEAR-WARRANTY FOR 3WOOD SERIES 
RESIDENTIAL HOT WATER BOILERS:

 QHT warrants that its 

cast-iron boiler and casing are free from defects in material and 
workmanship for one year from the date of installation. If the boiler 
is found to be defective within this period, QHT will replace the 
boiler block or casing. 
 

LIFETIME WARRANTY-WARRANTY FOR THE CAST IRON 
BOILER BLOCKS OF THE 3WOOD SERIES RESIDENTIAL 
BOILERS: 

Biasi warrants that the cast-iron sections and nipples 

of the BIASI 3WOOD boilers are free from defects in material and 
workmanship for the lifetime of the original single family home 
installation. If the 3WOOD boiler block is then found to be 
defective, QHT and Biasi will replace the original cast iron boiler 
block. 
 
These warranties are subject to the condition that a heating 
contractor whose principal occupation is the sale and installation 
of heating equipment must have installed the boiler. 
PARTS, WHICH ARE COVERED, consists of all materials 
supplied by Biasi, identified by QHT's part numbers in its 
literature. Other parts supplied in the casing, trim kit or in the 
burner pack carry their own warranty and each manufacturer has 
responsibility for its own products. 
 

NOTE: ANY PART, WHICH IS REPLACED UNDER 
WARRANTY, CARRIES ONLY THE UNEXPIRED PORTION OF 
THE ORIGINAL WARRANTY. 

OWNER RESPONSIBILITIES: 
1.  Provide for proper installation, which includes pressure relief 

and pressure reducing valves and high limit safety controls on 
closed systems. 

2.  Provide qualified periodic service to prolong proper operation 

and service. 

3.  Insure that boiler is installed with approved burner and that   

installation conforms to all codes and ordinances. 

4.  This warranty does not apply to boilers, which are subject to 

misuse, abuse, neglect, alteration, accident, excessive 
temperature, excessive pressure, or corrosive water or 
atmosphere. 

5.  Owner will be responsible for return of faulty components to 

QHT Inc. Portsmouth, NH, freight pre-paid. 

QHT and Biasi will not be responsible for: 
1.    Components that are part of the heating system, but 

were not manufactured by Biasi or QHT as part of the boiler. 

2.  The workmanship of the installers of  3WOOD boilers.   

Furthermore, this warranty does not assume any liability for 
unsatisfactory performance caused by improper installation. 

3.  Any costs for labor to remove or replace the faulty 

component. 

4.  Improper burner application or adjustments, control settings, 

care or maintenance. 

5.  Any damage associated with corrosion or leakage due to the 

use of "non-barrier", plastic pipe in the heating system. 

 
*THIS WARRANTY DOES NOT EXTEND TO ANYONE EXCEPT 
THE FIRST PURCHASER AT RETAIL AND ONLY WHEN THE 
BOILER IS IN THE ORIGINAL INSTALLATION SITE. 
*IMPLIED WARRANTIES OF FITNESS FOR A PARTICULAR 
PURPOSE AND MERCHANTABILITY SHALL BE LIMITED TO 
THE DURATION OF THE EXPRESSED WARRANTY. BIASI 
AND QHT EXPRESSLY DISCLAIM AND EXCLUDE ANY 
LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES 
FOR BREACH OF ANY EXPRESSED OR IMPLIED WARRANTY. 
 
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND 
YOU MAY HAVE OTHER RIGHTS THAT VARY FROM STATE 
TO STATE. 
 
For prompt warranty service, notify the installer, who, in turn, will 
notify the distributor from whom he purchased the boiler. If this 
does not result in corrective action, contact Biasi through Quincy 
Hydronic Technologies (Address Below) with details in support of 
the warranty claim. All claims must be processed through proper 
trade channels. Contact with Biasi directly is not recommended for 
rapid claim settlement. 
 

Quincy Hydronic Technologies,   

3560 Lafayette Rd. 

Portsmouth, NH,  03801 

Tel. (603) 334-6400 

Warranty for BIASI - 3WOOD Residential 

Cast-Iron Water Boilers 

NAME                                                                                                                 

STREET                                                                                                               

CITY                                                STATE           ZIP                       

BOILER SERIAL NO.                    DATE OF INSTALL                                                                   

NAME OF INSTALL CO.                                                                

STREET                                                                                                                  

CITY                                                      STATE          ZIP                       

B10 BOILER SIZE (EX. 4 SECTION)                                                                                       

SILVER RATINGS LABEL SERIAL # 

HOW DID YOU HEAR ABOUT BIASI? 

    DEALER/INSTALLER       WEBSITE      FRIEND/NEIGHBOR   

    OTHER

 

PLACE 

STAMP 

HERE 

BIASI BOILER WARRANTY REGISTRATION 

IMPORTANT., Registration required. To gain complete warranty  

protection, fill in and mail this card immediately. 

 
 
 

QHT Inc. 

3560 Lafayette Rd 

Portsmouth, NH 03801 

T

E

A

O

N

 THI

S

 LI

NE

 

Summary of Contents for BIASI 3 WOOD









































Reviews: